Ubbink Niagara LED 30 LED Instrucciones De Manejo página 3

1 Operating instruction for stainless steel waterfall ornaments Niagara 30 / 60 / 90 - 30 LED / 60 LED / 90 LED
This is a design waterfall from stainless steel for installation at garden ponds and smaller water basins. The models Niagara 30 LED / 60 LED / 90 LED are equipped with a This is a design waterfall from stainless steel for installation at garden ponds and smaller water basins. The models Niagara 30 LED / 60 LED / 90 LED are equipped with a
LED-strip to illuminate your stainless steel waterfall. LED-strip to illuminate your stainless steel waterfall.
Please read this operating instruction thoroughly before you start-up the Niagara waterfall with/without LED-lighting and keep this instruction safely. The waterfall s not Please read this operating instruction thoroughly before you start-up the Niagara waterfall with/without LED-lighting and keep this instruction safely. The waterfall s not
intended for operation in water containing chlorine and salt. intended for operation in water containing chlorine and salt.
Safety instructions for Niagara 30 LED / 60 LED / 90 LED Safety instructions for Niagara 30 LED / 60 LED / 90 LED
• The power supply of pump and LED strip must correspond to the product specifi cations. Do not connect pump, LED strip and power supply cable if the power supply does not meet
the specifi ed regulations! Your local approved electrician will provide you with further information.
• The plug connection of pump and LED strip must be carried out at a distance of over 3.5 m away from the garden pond.
• The power supply of pump and LED strip must be carried out via an insulation transformer or an earth leakage circuit breaker (FI - switch) with < 30mA nominal fault current.
• Always use a safety transformer IP X4 for outside areas. Please take notice that the transformer must only be operated at a distance of over 2 m away from the garden pond.
• The waterfall must only be operated with a pump suitable and certifi ed for this purpose.
• Never use the cable for carrying transformers and never pull the transformer by the cable.
• The power supply cable of the transformer and the lighting cannot be replaced. If the cable is damaged the device must not be operated anymore and disposed properly.
• The power supply must always be interrupted during assembly or disassembly of the pump or the LED strip and their maintenance.
• This waterfall as well as the LED strip and used pump are not suitable for use by persons (Including children) with reduced physical, sensory or mental capabilities or lack of
experience and knowledge unless these are supervised by a person responsible for their safety or have been instructed regarding the use of the devices. Children must be
supervised in order to ensure that they are not playing with the devices.
• The operating instruction and safety instructions of the used pump (Not part of the delivery volume) must absolutely be observed!
Installation Installation
Niagara 30 / 60 / 90 Niagara 30 / 60 / 90
1. Ensure that your waterfall, the hose connection and pump have been installed according to the assembly instruction.
2. You can then switch on the pump and start your waterfall.
Niagara 30 LED / 60 LED / 90 LED
1. Ensure that your waterfall, hose connection and pump have been assembled according to the assembly instruction.
2. Check the LED strip for correct fi t, route the LED-lighting cable to the outside of the waterfall element and connect it there with the safety transformer at a distance of at least
3,5 m away from the water basin.
3. You can then switch on the LED strip and pump and start up your waterfall.
Maintenance and care Maintenance and care
Cleaning of the bulbs
Use only water and a soft cloth. Pay attention that the glass of the LED diodes do not get scratched or damaged.
Replacing the bulbs
It is not possible to replace individual defect LED diodes. The aff ected LED strip must be removed and replaced.
Cleaning of the stainless steel waterfalls Cleaning of the stainless steel waterfalls
• Check the waterfall before installation for possible corrosion from, possibly, metals or chemicals not having been noticed initially.
• Start with weekly cleaning to determine and specify the optimum cleaning period. Pay attention that no deposits are formed (e.g. salts or other solids).
• No materials like salts, dust, dirt, etc. are allowed to deposit on the waterfall.
• Avoid direct contact with other metals; especially iron, concrete, etc.
• Cleaning of the waterfall can normally be carried out with not chlorinated basin water. Should fi rst indications of rust have formed, clean the parts with a stainless steel cleaner (No
scouring agent) or with nitric acid in a 10-15% water solution. Rinse the parts in both cases with fresh water and dry with a cotton wool cloth.
• Pay special attention to the intermediate areas (e.g. fastening of the LED strip) and deposits at the height of the water level.
• Check the pH-value regularly and pay attention to the correct use of disinfecting agents.
• Circulate the water every day, so that no deposits are formed on the stainless steel parts in contact with water.
• Check the stainless steel waterfall element during an annual preventive maintenance.
Information: You will have fewer problems with corrosion and the parts will be more corrosion resistant, if you are caring for and cleaning your Niagara waterfall regularly.
Repairs Repairs
No repair is possible if cable, LED strip or transformer is damaged. You must not use the respective part any longer and dispose it properly.
2
Guarantee
We guarantee this product for 2 years against proven material and manufacturing faults from the date of purchase. The original purchase receipt must be presented as proof of
purchase in case of guarantee claims. The guarantee does not extend to complaints caused by assembly or operating errors, a lack of care, the eff ects of frost, improper repair attempts,
the use of force, outside culpability, overloads, mechanical damage or the eff ects of foreign bodies. The guarantee likewise excludes all complaints concerning parts damage and/or
problems caused by wear and tear.
Correct disposal of this product
This symbol points out inside the EU that this product must not be disposed via domestic waste. Old devices contain valuable materials for recycling, which should be
passed on to recycling and not harm the environment or human health due to uncontrolled waste disposal. Please, dispose the old devices therefore via suitable collect-
ing systems or send the device for disposal to the place you bought it from. This will then pass on the device to recycling.
manual niagara led 2012.indd 1 19-03-12 12:48