Important Safety Information - Hatco THERM-MAX Salamander TMS Serie Instrucciones Originales

Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property
WARNING
ELECTRIC SHOCk HAzARD:
• Unit must be installed by a qualified electrician.
Installation must conform to all local electrical codes.
Installation by unqualified personnel will void unit
warranty and may lead to electric shock or burn, as well
as damage to unit and/or its surroundings.
• Units supplied without an electrical plug require field
installation of proper plug. Plug must be properly
grounded and of
configuration for electrical specifications of unit.
Contact a qualified electrician to determine and install
proper electrical plug.
• Units supplied without an electrical cord and plug
require field installation of proper cord and plug or a
hardwired connection to on-site electrical system.
Connection must be properly grounded and of correct
voltage, size, and
specifications of unit. Contact a qualified electrician to
determine and install proper electrical connection.
• When installing a hardwired unit, a 2-pole or 3-pole
switch (depending on unit) must be installed between
unit and main electrical supply. The switch must be
rated properly and have contacts with a minimum
opening distance of 3 mm (1/8").
• Turn OFF power switch, unplug power cord/turn off
power at circuit breaker, and allow unit to cool before
performing any cleaning, adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 21°C (70°F)
and a maximum of 29°C (85°F).
• Do not steam clean or use excessive water on unit.
• This unit is not "jet-proof" construction. Do not use jet-
clean spray to clean this unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power
cord. Cord must be replaced by Hatco, an Authorized
Hatco Service Agent, or a person with similar
qualifications.
• Do not clean unit when it is energized or hot.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
correct voltage, size,
configuration for electrical

IMPORTANT SAFETy INFORMATION

FIRE HAzARD:
• Install unit on and around non-combustible surfaces
with non-combustible construction only. Ensure surface
construction has no combustible material against
underside. In all cases, such construction shall extend at
least 305 mm (12") beyond equipment on all sides.
• Locate unit a minimum of 51 mm (2") from any walls. If
safe distances are not maintained, discoloration or
combustion could occur.
and
• Do not obstruct air intake openings or air exhaust
openings on outer housing of unit. Unit combustion or
malfunction may occur.
• Do not place anything on top of unit.
For wall mounting, use special wall mount bracket
provided with unit only. Secure wall mount bracket to a
solid, non-combustible surface using appropriate hardware
for mounting surface and weight of unit.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from the unit.
This unit has no "user-serviceable" parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at
414-671-6350; fax 414-671-3976.
BURN HAzARD:
• Some exterior surfaces on the unit will get hot. Use
caution when touching these areas.
• Plate/tray will be very hot upon removal — use oven
mitt, protective clothing, or pan gripper to remove.
Locate unit at proper counter height in an area that is
convenient for use. Location should be level to prevent unit
or its contents from falling accidentally and strong enough
to support the weight of the unit and contents.
Do not place anything on top of unit; doing so may subject
personnel to injury or damage unit.
Units are voltage-specific. Refer to specification label for
electrical requirements before beginning installation.
Do not lock ON timer knob. Unit has instant-on heating
elements designed to reach cooking temperatures quickly.
Locking ON timer knob will increase energy consumption
and may shorten life of heating elements.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
.
WARNING
CAUTION
NOTICE