Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
same from moving and scratching both surfaces. If the helmet visor fogs up and/or condensation forms between the visors,
check both for system correct assembly and stretching. An excessive and early stretch of the inner visor may result in exces-
sive adherence against visor surface and/or permanent deformations with subsequent inability to perform following adjustments
correctly. The extended use under special weather conditions may reduce system performance and result in partial fogging and
problems of condensation on the inner visor. In this case, remove the inner visor from the helmet visor and dry it with dry and
lukewarm air to restore system efficiency. Intense sweating /breathing, the use under particular weather conditions (low tem-
peratures, and/or high humidity and/or sudden changes in temperature or heavy rain) and intense and prolonged use may affect
the performance of the system and cause the fogging or formation of condensation on the inner visor. In such cases, after using
the helmet and to restore the system efficiency, remove the inner visor from the helmet visor and let it dry with dry and luke-
warm air. The same procedure must be applied to the helmet, in order to dry out humidity in case it has formed up as a con-
sequence of the conditions described above.
2
PINLOCK
®
INNER VISOR DISASSEMBLY
2.1 Remove the visor equipped with Pinlock
2.2 Widen the visor and release the Pinlock
2.3 Release the visor.
MAINTENANCE AND CLEANING
Remove the Pinlock
®
inner visor from the visor. Using a damp and soft cloth, gently clean it with neutral liquid soap. Remove
the soap under running water. Dry the inner visor with dry and lukewarm air without wiping it. To keep the features of the inner
visor in good conditions over time, let the helmet dry in a ventilated and dry place with the visor open after use. Keep it away
from heat sources and store it in a place away from direct light.
•
VISION PROTECTION SYSTEM (VPS)
The exclusive inner VISION PROTECTION SYSTEM (VPS) is a LEXAN
ant/fog-resistant treatment. Very simple and practical to use. Just lower to activate it or lift to remove it from the field of vision.
It is useful in all sorts of situations, both on long journeys out of town and shorter town trips.
Moreover, the innovative fastening system allows you to assemble and disassemble the sun screen without the need for any
tools for ordinary maintenance and cleaning operations.
(*)
LEXAN is a trademark of SABIC.
same from moving and scratching both surfaces. If the helmet visor fogs up and/or condensation forms between the visors,
check both for system correct assembly and stretching. An excessive and early stretch of the inner visor may result in exces-
sive adherence against visor surface and/or permanent deformations with subsequent inability to perform following adjustments
correctly. The extended use under special weather conditions may reduce system performance and result in partial fogging and
problems of condensation on the inner visor. In this case, remove the inner visor from the helmet visor and dry it with dry and
lukewarm air to restore system efficiency. Intense sweating /breathing, the use under particular weather conditions (low tem-
peratures, and/or high humidity and/or sudden changes in temperature or heavy rain) and intense and prolonged use may affect
the performance of the system and cause the fogging or formation of condensation on the inner visor. In such cases, after using
the helmet and to restore the system efficiency, remove the inner visor from the helmet visor and let it dry with dry and luke-
warm air. The same procedure must be applied to the helmet, in order to dry out humidity in case it has formed up as a con-
sequence of the conditions described above.
2
PINLOCK
®
INNER VISOR DISASSEMBLY
2.1 Remove the visor equipped with Pinlock
2.2 Widen the visor and release the Pinlock
2.3 Release the visor.
MAINTENANCE AND CLEANING
Remove the Pinlock
®
inner visor from the visor. Using a damp and soft cloth, gently clean it with neutral liquid soap. Remove
the soap under running water. Dry the inner visor with dry and lukewarm air without wiping it. To keep the features of the inner
visor in good conditions over time, let the helmet dry in a ventilated and dry place with the visor open after use. Keep it away
from heat sources and store it in a place away from direct light.
•
VISION PROTECTION SYSTEM (VPS)
The exclusive inner VISION PROTECTION SYSTEM (VPS) is a LEXAN
ant/fog-resistant treatment. Very simple and practical to use. Just lower to activate it or lift to remove it from the field of vision.
It is useful in all sorts of situations, both on long journeys out of town and shorter town trips.
Moreover, the innovative fastening system allows you to assemble and disassemble the sun screen without the need for any
tools for ordinary maintenance and cleaning operations.
(*)
LEXAN is a trademark of SABIC.
®
inner visor.
®
inner visor from the pins (Fig. 7).
™
7
inner visor.
®
®
inner visor from the pins (Fig. 7).
™
7
- polycarbonate moulded sun screen with scratch-resist-
(*)
(*)
- polycarbonate moulded sun screen with scratch-resist-
Publicidad
Tabla de contenido
