Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
-
Always make sure that the VPS is clean and that it is operating properly in order to avoid scratches and/or anomalous wear
on it every time it is activated.
-
Please refer to the proper section in the helmet user's manual for the VPS and visor maintenance and cleaning operations.
-
The VPS scratch-resistant and fog-resistant treatment highly reduces fogging. Protracted periods of adverse weather
and/or environmental conditions might cause fogging and/or formation of condensation on the VPS, which entails a reduc-
tion of visibility and/or sharpness of vision: in this case, deactivate the VPS.
-
In case of rain, the direct contact of raindrops with the scratch-resistant and fog-resistant treated VPS quickly reduces
sharpness of vision, thus causing scarce visibility: in this case, deactivate the VPS.
-
The special VPS fog-resistant treatment is usually sensitive to high temperatures or heat sources. In this case, contamina-
tions caused by contact with other materials might occur. These contaminations will cause marks and stains to develop. In
these cases (e.g. when the helmet is kept in the top case on hot days), it is recommended to make sure the VPS is not
touching other materials.
VPS DISASSEMBLY INSTRUCTIONS
To remove the VPS system from the helmet, open the chin guard and lower the VPS by pushing the side slider towards the back
of the helmet (Fig. 9 B).Hold the right lateral part of the VPS and lift the VPS to the outside of the helmet (Fig. 10). Repeat the
same operation on the left side of the helmet.
VPS ASSEMBLY INSTRUCTIONS
To fit the VPS system from the helmet, open the chin guard and make sure the side slider is placed towards the back of the hel-
met (Fig. 9 B). Insert the VPS left end into the left side guide until the grip pawl is hooked in shell housing (Fig. 11). Repeat the
same steps on the right side.
WARNING
-
Make sure the VPS works correctly by moving the left side slider forward (Fig. 9 A) and back-ward (Fig. 9 B) so that you can
hear the clicks meaning that it enters the relative positions. If necessary, repeat the above-mentioned steps.
-
If the visor and/or VPS opening/closing mechanisms are damaged or malfunctioning, please contact a Nolan authorised
dealer.
-
Do not use the helmet if the VPS has not been assembled properly.
-
The VPS doesn't replace the protection guaranteed by the visor. For this reason it must always be used only when the
helmet's visor is lowered.
-
Always make sure that the VPS is clean and that it is operating properly in order to avoid scratches and/or anomalous wear
on it every time it is activated.
-
Please refer to the proper section in the helmet user's manual for the VPS and visor maintenance and cleaning operations.
-
The VPS scratch-resistant and fog-resistant treatment highly reduces fogging. Protracted periods of adverse weather
and/or environmental conditions might cause fogging and/or formation of condensation on the VPS, which entails a reduc-
tion of visibility and/or sharpness of vision: in this case, deactivate the VPS.
-
In case of rain, the direct contact of raindrops with the scratch-resistant and fog-resistant treated VPS quickly reduces
sharpness of vision, thus causing scarce visibility: in this case, deactivate the VPS.
-
The special VPS fog-resistant treatment is usually sensitive to high temperatures or heat sources. In this case, contamina-
tions caused by contact with other materials might occur. These contaminations will cause marks and stains to develop. In
these cases (e.g. when the helmet is kept in the top case on hot days), it is recommended to make sure the VPS is not
touching other materials.
VPS DISASSEMBLY INSTRUCTIONS
To remove the VPS system from the helmet, open the chin guard and lower the VPS by pushing the side slider towards the back
of the helmet (Fig. 9 B).Hold the right lateral part of the VPS and lift the VPS to the outside of the helmet (Fig. 10). Repeat the
same operation on the left side of the helmet.
VPS ASSEMBLY INSTRUCTIONS
To fit the VPS system from the helmet, open the chin guard and make sure the side slider is placed towards the back of the hel-
met (Fig. 9 B). Insert the VPS left end into the left side guide until the grip pawl is hooked in shell housing (Fig. 11). Repeat the
same steps on the right side.
WARNING
-
Make sure the VPS works correctly by moving the left side slider forward (Fig. 9 A) and back-ward (Fig. 9 B) so that you can
hear the clicks meaning that it enters the relative positions. If necessary, repeat the above-mentioned steps.
-
If the visor and/or VPS opening/closing mechanisms are damaged or malfunctioning, please contact a Nolan authorised
dealer.
-
Do not use the helmet if the VPS has not been assembled properly.
-
The VPS doesn't replace the protection guaranteed by the visor. For this reason it must always be used only when the
helmet's visor is lowered.
9
9
Publicidad
Tabla de contenido
