Denon DN-S1000 Instrucciones De Operación página 9

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

!8
DISC MODE button
Select from Scratch playback, Bend mode or
Manual Frame Search mode.
• SCRATCH:
This button lights up or blinks in orange when
scratching. Manipulate the sound by pushing
down on the disc, move it and then release it.
• BEND/SEARCH:
When the Disc mode is set to BEND during
playback, it alternates as the pitch bend
function. The display will indicate "Bend".
When Disc mode is set to Search, during
Pause or CUE mode, it alternates as the
Manual Search function. Manual search allows
you to move the CUE point around by one
frame at a time (1/75 second) with an audible
frame-repeat sound. The display will indicate
"Search".
!9
FILTER button
• One of three filters (LOW PASS, MID PASS
and HIGH PASS) can be selected.
@0
FLANGER button
• The feedback time and feedback gain can be
selected.
@1
TAP,
LOCK,
AUTO, INPUT BPM
button
• TAP:
When you push this button repeatedly, the
Auto mode turns off and starts measuring your
Beats Per Minute (BPM) by tapping.
• LOCK:
When this button is pressed once while the
auto BPM counter is operating, the data
measured by the auto BPM counter is locked.
• AUTO:
When pushing the TAP button for 1 second,
activates AUTO BPM mode.
The measured BPM is displayed in the
character section of the display.
• INPUT BPM:
When the TAP button is pressed and held in
for more than 2 seconds, the BPM input mode
is set and the BPM value can be input directly
with the PARAMETERS knob. When the tap
button is pressed again, the BPM input mode
is turned off and set.
NOTE:
If you select a new track, AUTO BPM mode turns
back on automatically.
@2
ECHO/LOOP button
• The ECHO and LOOP functions can be
selected. The feedback time and feedback
ratio can be selected. Looping for the
feedback time (ECHO LOOP) is possible by
setting the feedback number to "MAX".
@3
TRACK/PARAMETERS knob
• TRACK:
When PARAMETERS LED is on, turn this knob
to select tracks.
By pushing this knob down while turning, the
tracks will change by 10 tracks at a time.
• PARAMETERS:
When the PARAMETER LED is flashing, turn
this knob to select and change the parameter
for items found in the Platter effects, Memo,
and Preset data, etc.
• FILE SEARCH MODE:MP3 DISC only.
When pushing this knob for more than 1
second, the file search selection mode is
selected.
@4
FAST SEARCH (6)
QUICK JUMP button
@5
FAST SEARCH (7)
QUICK JUMP button
• QUICK JUMP:
When one of these buttons is tapped shortly,
the playback position jumps approximately 10
seconds in the forward (
7
) or reverse (
direction. The jump time can be changed in the
preset mode.
• FAST SEARCH:
When one of these buttons is pressed and
held in, the disc is fast-searched in the forward
(
7
) or reverse (
6
) direction.
@6
PITCH BEND – button
@7
PITCH BEND + button
• Pushing these buttons will change main
playing speed temporarily.
• While pushing PITCH BEND + button, the
playing speed increases and speed decreases
while pushing PITCH BEND – button.
• When release button, playing speed returns to
the previous speed.
@8
Pitch Slider
• Use this slider to adjust playing speed.
• The playing speed decreases when slid
upwards and increases downwards.
@9
PITCH/KEY,
RANGE button
• With this button you can select PITCH and
KEY ADJUST mode. Mode changes Pitch on,
Key Adjust on and both off cyclically. PITCH
LED indicates in Pitch mode and KEY ADJUST
indicator in the display lights up in Key Adjust
mode.
• RANGE:
Push this button for more than 1 sec to select
the pitch range. The pitch range can be
selected with the PARAMETERS knob from
±4,10,16,24 or 100%.
#0
RVS button
• Push this button to set the RVS mode.
#1
BRAKE button
• Push this button to set the BRAKE.
#2
DRAG-S button
• Push this button to set the DRAG-S.
6
)
ENGLISH
9

Publicidad

Tabla de contenido
loading

Tabla de contenido