Display + Controls - EcoxGear EcoBoulder GDI-EXBM900 Manual De Instrucciones

Display + Controls

12
11 10 9
Rubberized
Device Pad
1. Power Button:
Turns EcoBoulder on or off.
2. Bluetooth Button:
When in Bluetooth mode, if the Bluetooth icon is not
flashing on the LED screen, press this button to enter pairing mode. If your device
is paired (solid icon on LED screen), press button to disconnect. Press and hold this
button for 5 seconds to clear all pairing records.
3. Source Button:
Press this button to cycle through the following modes:
Bluetooth, FM, AM, AUX 1, and AUX 2.
4. Play/Pause:
Press to play or pause a track from a paired Bluetooth device.
5. Track Buttons:
Press these buttons to go to the previous/next track on a paired
Bluetooth device.
6. Microphone Volume Control:
and hold to adjust the volume continually (volume levels are 0 to 30).
7. EcoConnect Button:
If you have purchased a second EcoBoulder, press and
release this button on both speakers to link them together and play in stereo.
8. Master Volume Control:
Press to adjust the speaker's main mix volume. Press
and hold to adjust the volume continually (volume levels are 0 to 30).
13 3 2 1
4 5
8 7 6
Secure Cradle
TOP
for Devices
Press to adjust the microphone volume. Press
9. Backlight Button:
10. Tune Buttons:
Press these buttons to tune in a radio station. To "seek" (jump
to the next available station), press and hold either button down for a few seconds
until it starts to seek a station.
11. Radio Selector:
12. AM/FM Presets:
station. There are 6 positions for AM stations and 6 positions for FM stations. Press
and hold a preset button (P1~P6) to assign the currently playing station to that
preset number. The LED screen will flash 2 times to indicate it has been set. To use
a saved preset, press a preset button (P1~P6) to go to the previously saved station.
13. LED Screen Icons:
Indicates the battery level of
the EcoBoulder.
Indicates the battery is
very low.
Indicates the EcoBoulder
is charging.
The EcoBoulder is in
FM mode.
The EcoBoulder is in
AM mode.
The EcoBoulder is in
AUX1 mode.
The EcoBoulder is in
AUX2 mode.
14. Power Save Mode:
when the internal battery is low. "Chg" will be flashing on the LED screen when the
EcoBoulder enters Power Save Mode. Please recharge the internal battery once you
see the "Chg" display.
· Power Save Mode is active when battery level is 10% or less.
· Power Save Mode limits the unit functions in order to prolong play time
and allow the internal battery to recharge more quickly.
a. When in Power Save Mode the volume will be limited to half. (15 of 30)
b. When in Power Save Mode the USB charge out ports will be turned off.
· Once the EcoBoulder is adequately charged, the unit will automatically exit
Power Save Mode and return to full functionality ("Chg" will no longer flash
on the LED screen).
10
Press to turn button backlights on / off.
This button sets the tuner to AM or FM.
Store a favorite radio station and quickly tune to a preset radio
Two EcoBoulders are connected.
In pairing mode, the icon will
flash. If the connection is
successful, the icon will be solid.
The EcoBoulder is in the
Bluetooth mode.
Indicates the speaker volume
level of EcoBoulder. (0 to 30)
Indicates the microphone vol.
level of EcoBoulder. (0 to 30)
Indicates the current FM
station of the EcoBoulder.
Indicates the current AM
station of the EcoBoulder.
The EcoBoulder is designed to enter Power Save Mode
11