Tabla de contenido
Publicidad
INICIO RÁPIDO en 4 PASOS
Abra la TAPA en la PARTE TRASERA de su ECOPEBBLE.
1
Encienda el INTERRUPTOR DE ALIMENTACIÓN
2
PRINCIPAL. Escuche el anuncio: "Power On" / "Power
On, Pairing Ready" y busca el panel posterior LED que
parpadee en azul.
Busque una conexión Bluetooth en su Smartdevice y
3
seleccione 'ECOXGEAR'. Escuche el anuncio:
"Bluetooth Connected."
Escoja y reproduzca su música desde su Smartdevice.
4
Notas IMPORTANTES
•
EL INTERRUPTOR DE ALIMENTACIÓN PRINCIPAL debe estar en la posición de encendido para que pueda
utilizar su ECOPEBBLE.
•
Cuando el Interruptor de alimentación principal esté encendido, utilice el botón en espera para encender/
apagar la unidad.
•
Mantenga pulsado el botón en espera por 3-5 segundos para encender/apagar su ECOPEBBLE.
•
Cuando NO utilice la unidad por períodos prolongados, coloque el Interruptor Principal de alimentación en
la posición apagado.
•
Conecte automáticamente a su dispositivo utilizando el botón de espera sólo al encender / apagar, y no apague
el interruptor principal. Cuando el interruptor principal se desactiva, se restablece el ECOPEBBLE y conexiones
anteriores se borran de la memoria. Cuando el interruptor principal se pone en ON , usted tiene que emparejar
a su dispositivo de nuevo.
SAFETY
This product has a limited life span of use and should be replaced when it shows obvious signs of wear.
Do not modify or remove any original component parts of the speaker. Doing so could cause damage to the unit allowing water to ingress. A unit with water
ingress should not be charged due to potential risk of fire or shock.
Do not attempt to mount the unit except with the approved ECOXGEAR mounts. Doing so could cause damage to the unit allowing water to ingress. A unit with
water ingress should not be charged due to potential risk of fire or shock.
Please exercise care and good judgment when using your ECOXGEAR speaker. Audio levels should be appropriate to your environment, comply with all local
regulations, and always ensure that you can hear and be aware of any potential hazards around you.
You should always
1) Use the ECOXGEAR speaker in accordance with any music or noise rules and regulations.
2) Use the proper ECOXGEAR mounts if you intend to mount the unit.
3) Properly seal the ECOXGEAR prior and after each use when in humid or water environments to avoid water damage to the internal components. Salt
water / air is particularly corrosive. Always make sure that the gaskets are sealed when in salt water environment and the unit properly rinsed off after use.
4) Properly clean the ECOXGEAR and ensure the gaskets have no sand, dirt or water on them prior to storage or removing the back cover.
5) Store your unit with all caps properly sealed to avoid long term internal moisture damage inside your unit.
6) Completely dry and clean your ECOXGEAR prior to attempting to charge the unit.
7) Return the ECOXGEAR to Grace Digital if you suspect water ingress into the unit or if the unit has experienced a severe impact that may have affected the
integrity of the unit to take on water.
You should never
1) Charge your ECOXGEAR if you suspect water has entered the device. Charging a device with water inside could be potentially hazardous and cause fire or
a spark.
2) Use your ECOXGEAR if you have dropped it or thrown it against a hard surface which may have destroyed the integrity of the speakers, housings or
gaskets. In the event of a severe impact to your unit please return the unit to Grace Digital to review for potential damage.
3) Open the auxiliary door in a water environment. This could cause water to ingress into the unit which could potentially be hazardous and cause a fire or
a spark.
4) Connect a device to the auxiliary input jack when in a water environment. The auxiliary jack should only be used in a dry environment.
5) Attempt to fix, repair your ECOXGEAR unit. Please send it back to Grace Digital for any assessments and repairs.
Publicidad
Tabla de contenido
