Publicidad
Idiomas disponibles
Idiomas disponibles
Series 450 -453
DOUBLE ACTING CYLINDER, Ø 32 to 100 mm
Type: PES-DM
WITH STATIC ROD-LOCKING DEVICE
Complying with VDMA 24562-AFNOR-ISO 6431 standards
GB
Equipped for magnetic position detection
APPLICATION PRINCIPLE
The static rod-locking device with or without manual override is fitted to
series 450 and 453 PES type cylinders with profiled barrel or tie-rods. It is
designed to hold the rod of the cylinder under load in the extended or retracted
position in the event of air pressure or power failure during machine opera-
tion. The rod-locking device acts mechanically on the cylinder rod. It is
unlocked when pressure is applied.
Advantages
Easily accessible and quick-to-operate manual override (3/4 turn).
●
●
Possibility of integrating the following options associated to the manual
override:
- Integrated rod-lock pilot control.
- Detection (magnetic or electro-mechanical) of the position of the manual
override.
- Cylinder startup interlock system (Ø 80-100 mm).
Simple adaption. The compactly sized rod-locking device has approxi-
●
mately the same dimensions of a standard cylinder.
●
Possibility of mounting to specially designed cylinders (with overlength
piston rod) complying with VDMA-ISO6431-AFNOR standards.
Holding of the piston rod in the end-of-stroke position: with rod extended
●
or rod retracted side.
●
Holding in position of the maximum allowable cylinder load without creeping.
●
Bi-directional action.
Optional mounting position.
●
OPERATING PRINCIPLE
■ NO PRESSURE ON STATIC ROD-LOCKING DEVICE (rod locked)
No pressure is transmitted to the locking pistons (1). The springs (3) apply an axial
force onto the two jaws (2) which clamp against the rod, holding it secure.
Top view
2
1
2
2
1
3
■ ROD-LOCKING DEVICE PRESSURISED (rod unlocked)
The pressure exerts a force on the 2 pneumatic pistons (1) which come into contact with
the two jaws (2), clamping them together. The 2 jaws no longer exert any force on the
rod which is free to move.
Top view
Air supply
2
1
2
3
2
1
3
THIS PRODUCT IS NOT A SAFETY COMPONENT
Do not disassemble the individual product
components. Return the complete unit consisting
of cylinder + rod-locking device.
OPERATING PRINCIPLE
OF THE
MANUAL OVERRIDE
■ NO PRESSURE ON STATIC ROD LOCK
(rod locked)
Operate the manual override to disen-
gage the rod.
Front view
3/4 turn
3
2
Wrench
(8 mm)
2
Top view
Rod "disengage"
position
4
1
Front view
2
Actuating the manual override (4) by a ¾
turn makes the piston (5) come into contact
with the two jaws (2), clamping them to-
gether. The 2 jaws no longer exert any
force on the rod which is unlocked.
Caution: After having operated the
manual lock-up override, it must always
be returned to its normal operating po-
sition (rod lock "activated") by a trained
and qualified person before starting up
the system again.
1
GENERAL SPECIFICATIONS
ASSEMBLY
CYLINDER
CYLINDER TYPE
CYLINDER BORE DIAMETERS
STANDARD CYLINDER STROKES
AMBIENT TEMPERATURE
MOUNTING POSITION
MOUNTINGS
STATIC ROD LOCK
FLUID
DISENGAGE PRESSURE
MAX. SYSTEM PRESSURE
AMBIENT TEMPERATURE
PNEUMATIC CONNECTION
MOUNTING POSITION
MECHANICAL CHARACTERISTICS
HOLDING FORCES (static)
Example for holding force on a dia. 80 mm cylinder:
Attached weight (corresponding to a pressure of 6 bar and a 75 % load factor) = 2250 N
Additional force (equivalent to a pressure of 6 bar) = 3150 N
CONNECTION OF ELECTRO-MECHANICAL DETECTOR
4
VOLTAGE = 24 V DC
5
2
Fastening with 2 screws
MOUNTING OF SOLENOID VALVE
Normal operating
position
0
✶
+ 10 mm for connector clearance
PES CYLINDER + STATIC ROD-LOCKING DEVICE
: Rod lock device incorporated into cylinder, fitted in line, centered on the piston rod
: Series 450-453 cylinder type PES with tie-rods conforming to VDMA 24562-AFNOR NFE
49003- ISO 6431 standards, aluminium barrel, adjustable pneumatic cushioning, designed
for Reed switches, magneto-resistive or magneto-inductive position detectors.
: Ø 32 - 40 - 50 - 63 - 80 - 100 mm.
: 50 to 600 mm (or more, consult us).
: -20°C to +60°C
: Optional, see assembly recommendations below.
: All standard mountings for PES cylinders with tie-rods (see P229, P230 oder P232).
Centre trunnion: consult us.
: Air or neutral gas, filtered, lubricated or unlubricated
: 2.5 bar (min.)
: 10 bar
: -5°C, +70°C
: G1/8 (Ø32 - 63) - G1/4 (Ø 80 - 100)
: Optional, see following pages for assembly recommendations.
Ø 32 mm : 790 N
Ø 50 mm : 1930 N
Ø 40 mm : 1240 N
Ø 63 mm : 3060 N
5400 N = 2250 N + 3150 N
Holding force
Attached
Additional force
of static rod lock
weight
0.5 m
black = common
brown = NC
blue = NO
Exhaust (3)
Outlet (2)
Pressure supply (1)
4,5
20
9,7
50
*
15
Top view
2
Ø 80 mm : 5400 N
Ø 100 mm : 7700 N
Mounting
surface
3 holes Ø2
2 holes Ø3,5
9,7
= =
15
=
=
Publicidad
