Publicidad
L I B E R T Y ™ S e r i e s
City-Wide Surveillance
Installation and Operation Instructions for the following models:
LDW75CLG
Liberty Series wireless IP Ready dome. Include cellular
router, power supply for the complete system. Cellular
broadband adapter sold separately. 110/220VAC input.
Designed to work with Moog-Videolarm's IP Ready Series
of IP camera housings.
Before attempting to connect or operate this product,
please read these instructions completely.
CERTIFIED
81-IN5453
05-17-2010
Publicidad
Tabla de contenido
Manuales relacionados para Moog Videolarm LIBERTY LDW75CLG
Resumen de contenidos para Moog Videolarm LIBERTY LDW75CLG
- Página 1 L I B E R T Y ™ S e r i e s City-Wide Surveillance Installation and Operation Instructions for the following models: LDW75CLG Liberty Series wireless IP Ready dome. Include cellular router, power supply for the complete system. Cellular broadband adapter sold separately.
-
Página 2: Important Safeguards
IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS Read these instructions. Keep these instructions. CAUTION Heed all warnings RISK OF ELECTRIC SHOCK DO NOT OPEN Follow all instructions. Do not use this apparatus near water. CAUTION: TO REDUCE THE RISK OF Clean only with damp cloth. ELECTRIC SHOCK, DO NOT REMOVE Do not block any of the ventilation openings. - Página 3 LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship,as follows: PRODUCTCATEGORY PARTS LABOR All Enclosures and Electronics Five (5) Years Five (5) Years Pan/Tilts Three (3) Years **6 months if used in autoscan Three (3) Years **6 months if used in autoscan /tour operation /tour operation...
-
Página 4: Electrical Specifications
Content of Box Electrical Specifications LDW75CLG 120/240 VAC 50/60Hrz. 96 Watts Accessories: Heater: 50 Watts, Blower: 2 Watt Camera Power: (See Camera Specifications): 40 Watts Max English 120/240VAC 50/60Hrz. 96 Vatios De Accesorios: Calentador: 50 Watts, Blower: 2 Vatio Energía De la Cámara fotográfica De : (Véase Las Especificaciones De la Cámara fotográfica): 40 Vatios De Herramientas Máximas Español... - Página 5 Power Feed Locations: LIQUID TIGHT PLUG FOR 3G ANTENNA BULKHEAD CONNECTOR HOLE. LIQUID TIGHT PLUG FOR OPTIONAL MAIN POWER HOLE. LIQUID TIGHT PLUG FOR OPTIONAL MAIN POWER HOLE. LIQUID TIGHT STRAIN RELIEF FOR MAIN POWER HOLE.
- Página 6 POLE MOUNTING Holes for steel straps LDW75CLG unit is ready to mount. Use marked Use the steel straps to mount the unit to pole. holes to attach steel straps. • Utilice las correas de acero para montar la unidad al •...
-
Página 7: Wall Mounting
WALL MOUNTING Tilt the unit to align the grooves (holes) to the Wall mount option. lips on the bracket. • Incline la unidad para alinear los surcos (agujeros) con • Opción del montaje de la pared. los labios en el soporte. •... - Página 8 To assemble a camera or for the maintenance of the Remove the dome and follow the specified unit (if needed) you should flip so that the dome is camera mounting options. facing upwards. • Quite la bóveda y siga las opciones especificadas del •...
- Página 9 To open the top cover unlock the latches. Top inside view of the unit. From here you can activate the unit • Para abrir la cubierta superior abra los cierres. Aquí de usted • Tapa dentro de la vista de la unidad. puede activar la unidad.
- Página 10 3G/4G Camera Prep Assign your camera to DHCP and the DNS to Connect to your camera with a laptop or pc DHCP. • Conecte con su cámara con un ordenador portátil o • Asigne su cámara al DHCP y al DNS al DHCP. una PC.
- Página 11 Use the provided velcro to mount and secure the USB modem. • Utilice el Velcro proporcionado para montar y para asegurar el módem del USB. • Employez le Velcro fourni pour monter et fixer le modem d'USB. • Benutzen Sie den zur Verfügung gestellten Flausch, um das USB-Modem anzubringen und zu sichern. •...
- Página 12 LIST OF 3G / 4G SUPPORTED USB CARDS BY PROVIDERS: 3 (UK) Alltel B-Mobile (Japan) AT&T Huawei E156G Franklin CDU-550 Option Quicksilver ZTE MF626 Bell (Canada) BridgeMAXX Wimax Huawei EC168/C Sierra Wireless 881U Huawei EC228 Sierra Wireless 875U Novatel Wireless U760 ZTE TU-25 Bell Mobility U998 HPSA+ Turbo Cricket...
- Página 13 Captive Axis 213 (3) #8x3/8” Screw Mounting Plate ½" 1" 2" MOUNTING HOLE MOUNTING HOLE Install the camera to the mounting plate with (2) #10 screws and lock washers provided. Place (3) #8x3/8” screws on the spacers and align the mounting slots. Slide on plate and camera then secure. •...
- Página 14 Axis 215 (3) #8x3/8” Mounting Plate 1" 1" 2" MOUNTING HOLE MOUNTING HOLE Install the camera to the mounting plate using (4) #8 bolts and lock washers. Place (3) #8x3/8” screws on the spacers and line up the mounting slots. Slide plate in and secure. •...
- Página 15 AXIS 231-232D AXIS 231-232D Locking screw Loosen Screw Loosen the screw to the right of the tab by Align mounting plate and turn counter- approximately (5) turns. clockwise, secure locking screw. • Alinee la placa de montaje y dé vuelta a la •...
- Página 16 Open Screw Slots Cable Ties POWER Camera Power (24VAC) Orange Camera Power (24VAC) CONTROL RJ45 Ethernet Connector ALARMS Alarm 1 Blue Alarm 2 Violet Alarm 3 Gray Common White Captive Screw Complete the wiring to camera. Attach the camera assembly to the housing by sliding the (3) This is what the typical path of illumination will look like with the setting at 30 degrees.
- Página 17 Axis 233D Slots Fastener Position camera and mounting plate on top of spacers. Secure quick release turn plate by tightening (3) bolts and (1) fastener. • Asegure la placa rápida de la vuelta del lanzamiento apretando (3) los pernos y (1) la cámara fotográfica del sujetador en la posición usando ranuras.
- Página 18 Axis 233D Important information for the model of camera. English Due to the high 35x zoom feature of the Axis 233D camera, a slight focus issue may occur when the camera lens is fully extended within the Videolarm camera housing. For applications where the full 35x high-powered zoom is needed, please contact Videolarm to request a complimentary enhanced optically clear acrylic dome.
- Página 19 CANON - VB-C10 Captive Screw Mounting Plate (3) #8x3/8” 1" 2" MOUNTING HOLE MOUNTING HOLE Install the camera to the mounting plate with (2) #10 screws and lock washers provided. Place (3) #8x3/8” screws on the spacers and align the mounting slots. Slide on plate and camera then secure. •...
- Página 20 ELMO 400/401 Captive (4) #8x3/8” Screw Mounting Plate 1" 1" 2" MOUNTING HOLE MOUNTING HOLE Attach camera to mounting plate using (4) #8 screws, star washer, and nuts. Complete assembly as shown, then secure camera to the quick release plate. •...
- Página 21 JVC-VN625U Captive (4) #8x3/8” Screw Mounting Plate ½" 1" MOUNTING HOLE Attach quick release bracket to mounting plate using (4) #8 screws and star washer. Complete assembly as shown, then secure camera to the quick release adapter. • Una el soporte rápido del lanzamiento a la placa de montaje usando (4) los tornillos #8 y la arandela de la estrella. Termine a asamblea como cámara fotográfica demostrada, después segura a la placa rápida del lanzamiento.
- Página 22 Panasonic KX-HCM180 Captive (3) #8x3/8” Screw Mounting Plate ½" 1" 2" MOUNTING HOLE Attach camera bracket to mounting plate using (1) ¼” x 20 bolt, lock washer, and washer. Complete assembly as shown, then secure camera to the quick release plate. •...
- Página 23 Panasonic WV-NS954 (4) #8x3/8” Mounting Plate 1" MOUNTING HOLE Attach bracket to (4) spacers using (4) #8 screws and star washer. Complete assembly as shown, then secure camera to the quick release plate. • Ate el soporte (4) a los espaciadores usando (4) los tornillos #8 y arandela de la estrella. Termine a la asamblea como se muestra, entonces cámara segura a la placa del lanzamiento rápido.
- Página 24 Sony RZ30 Captive (3) #8x3/8” Screw Mounting Plate ½" 2" MOUNTING HOLE Attach camera to mounting plate using (1) ¼” x 20 bolt, washer, and lock washer. Complete assembly as shown, then secure camera to the quick release plate. • Ate la cámara a la pletina usando (1) perno de x 20 del ¼”, arandela, y arandela de cerradura. Termine a la asamblea como se muestra, entonces cámara segura a la placa del lanzamiento rápido.
- Página 25 TOA 2564 Captive (4) #8x3/8” Screw Mounting Plate MOUNTING HOLE Attach camera to mounting plate using (4) #8 screws and star washer. Complete assembly as shown, then secure camera to the quick release plate. • Ate la cámara a la pletina usando (4) los tornillos #8 y arandela de la estrella. Termine a la asamblea como se muestra, entonces cámara segura a la placa del lanzamiento rápido.
- Página 26 Pixord 261/263 Captive (3) #8x3/8” Screw Mounting Plate ½" 1" MOUNTING HOLE Attach camera bracket to mounting plate using (3) #8 x ⅜” bolts, washer, and nuts. Complete assembly as shown, then secure camera to the quick release plate. • Ate el soporte de la cámara a la pletina usando (3) pernos, arandela, y las tuercas del ⅜ de #8 x los”. Termine a la asamblea como se muestra, entonces cámara segura a la placa del lanzamiento rápido.
-
Página 27: Replacement Parts
Replacement Parts LDW75CLG Liberty Series PART # DESCRIPTION 1 RP40VL3707 TOP COVER ASSEMBLY 2 RPLBHNG TOP COVER HINGES, LEFT&RIGHT 3 RP30VL3708 HINGE PLATE 4 RP96GK3710 TOP COVER GASKET 5 RP70VL3727 BOARD SHIELD 6 RP76VL2007 4G POWER & CONNECTION BOARD ASSEMBLY 7 RP96SJ355012 1/2"... -
Página 28: Product Registration/Warranty
Product Registration/Warranty Thank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the highest quality products available with unmatched customer service levels that are second-to-none in the security industry. Should a problem arise, rest assure that Videolarm stands behind its products by offering some of the most impressive warranty plans available: 3 Years on all Housings, Poles, Power Supplies, and Accessories and 5 Years on all camera systems (SView, QView, Warriors), and InfraRed Illuminators.