Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Light Kit
Installation Guide
Guide d'installation
de kit d'éclairage
Guía de instalación
del juego de luces
Assembly: Estimated assembly time is 35 minutes.
Assemblée: Le temps de montage est de 35 minutes environ.
Asamblea: El tiempo aproximado para armar es 35 minutos.
CAUTION
Disconnect Power
Always shut off power at the circuit breaker or disconnect fuse
when installing or repairing this, or any other electric appliance.
1. Assembly
Cap Style Hub
1. Remove three screws from side of switch hub (as shown in figure
below).
2. Remove hub cover from hub and pop out center plug.
3. Carefully thread wires from light kit through the center hole in hub
efully thr
efully thr
om light kit through the center hole in hub
om light kit thr
cover. At this point attach light kit into hub cover by scr
At this point attach light kit into hub cover by scr
At this point attach light kit into hub cover by scr
At this point attach light kit into hub cover by scr
all-thread from light kit into the center hub cover.
4. Lock the all-thread in place on the inside of the hub cover using the
3/8" nut provided.
5. Attach white wire from light kit to white wire in hub, using wire nuts.
Next, attach black wire from light kit to blue wire in switch hub.
6. Carefully push wires up into hub and replace hub cover using screws
efully push wir
efully push wir
removed earlier
emoved earlier
.
Screws
Center Screw
E1
FAILURE TO
DO SO MAY
RESULT IN
SEVERE
INJURY
ORDEATH.
ough the center hole in hub
ewing center
Switch Hub
3/8" Nut
Center Plug

Publicidad

loading

Resumen de contenidos para Craftmade F390

  • Página 1 FAILURE TO CAUTION DO SO MAY RESULT IN Disconnect Power SEVERE Always shut off power at the circuit breaker or disconnect fuse INJURY when installing or repairing this, or any other electric appliance. ORDEATH. 1. Assembly Light Kit Cap Style Hub Installation Guide 1. Remove three screws from side of switch hub (as shown in figure below).
  • Página 2 F390 Fitter Type F390 Fitter Type F390 Fitter T Harness Style Hub Harness Style Hub Harness Style Hub Harness Style Hub Harness Style Hub Harness Style Hub Harness Style Hub Remove three screws from side of switch hub (as shown in figure...
  • Página 3 DLK Light Kit will only fit the following fans: Fresco Old Madrid Constantina Crescent 1. To remove switch housing hub from fan, unscrew one screw and loosen other 2 from the side of the switch housing hub (as shown in Diagram A below). 2.
  • Página 4 Toll Fr ee Fax: (877) 304-1728 cap and then finial should be threaded securely onto pipe nipple 5) Reattach the breakaway connector and chain extension to both the motor pull email: customerservice@craftmade.com chain and light kit pull chain. www.craftmade.com www.craftmade.com...
  • Página 5 PROPER CARE MORTELLES In order to maximize the appearance of a Craftmade brass lighting fixture, it is important that dust and debris is removed from the surface of the lighting fixture periodically. It is recommended that 1. Assemblée the lighting fixtures be wiped down weekly using a soft, dry or damp cloth.
  • Página 6 Moyeu du type à faisceau Moyeu du type à faisceau Moyeu du type à faisceau Moyeu du type à faisceau Type à adaptateur F390 Type à adaptateur F390 ype à adaptateur F390 ype à adaptateur F390 ype à adaptateur F390 ype à...
  • Página 7 Le kit d’éclairage DLK ne s’adapte qu’aux ventilateurs suivants : Fresco Old Madrid Constantina Crescent 1. Pour déposer le moyeu à interrupteur du ventilateur, dévisser une des vis et desserrer les 2 autres sur le côté du moyeu (comme indiqué sur le Schéma A ci-dessous). Retirer 2.
  • Página 8 Email: customerservice@craftmade.com 5) Raccrocher le raccord détachable et la rallonge de chaî n e à la chaî n e à tirer du moteur et www. craftmade.com...
  • Página 9: Instalación

    1. Instalación ENTRETIEN CORRECT Afin de conserver au maximum l’aspect d’origine d’une applique en laiton CRAFTMADE, il est Afin de conserver au maximum l’aspect d’origine d’une applique en laiton CRAFTMADE, il est Afin de conserver au maximum l’aspect d’origine d’une applique en laiton CRAFTMADE, il est Afin de conserver au maximum l’aspect d’origine d’une applique en laiton CRAFTMADE, il est...
  • Página 10 Cubo estilo arnés Tipo ajustable F390 Tipo ajustable F390 ipo ajustable F390 ipo ajustable F390 ipo ajustable F390 ipo ajustable F390 Quite los tres tornillos situados al lado del cubo del interruptor es tornillos situados al lado del cubo del interruptor es tornillos situados al lado del cubo del interruptor 1.
  • Página 11 La lámpara DLK es adecuada sólo para los siguientes ventiladores: ventiladores: ventilador Fresco Old Madrid Constantina Crescent 1. Para quitar el eje de la caja del interruptor del ventilador, quite un tornillos y afloje los Tornillos Tornillos Retirar otros dos del costado del eje (tal como se muestra en el Diagrama A a continuación). 2.
  • Página 12 Correo electrónico: firmemente en el niple del tubo. customerservice@craftmade.com 5) Reconecte el conector y la extensión de la cadena a la cadena del motor y a la cadena de www. craftmade.com www. craftmade.com...
  • Página 13 CUIDADO APROPIADO Para optimizar el aspecto de un farol de latón CRAFTMADE, es importante quitar el polvo y Para optimizar el aspecto de un far Para optimizar el aspecto de un far Para optimizar el aspecto de un far...