Publicidad
Idiomas disponibles
Idiomas disponibles
F52
Screws
F52 & F54 Type
F52 & F54 T
F52 & F54 Type
Remove three screws from side of switch hub (as shown).
1.
Remove bottom portion of hub cover fr
Remove bottom portion of hub cover fr
Remove bottom portion of hub cover fr
Remove bottom portion of hub cover fr
Remove bottom portion of hub cover fr
Remove bottom portion of hub cover fr
Remove bottom portion of hub cover from hub.
2.
3.
Attach white wir
Attach white wir
e fr
e fr
om light kit to white wir
om light kit to white wir
Next, attach black wire from light kit to blue wire in switch hub.
om light kit to blue wir
om light kit to blue wir
For the F54 model, locate both modular wiring plugs. One extends
For the F54 model, locate both modular wiring plugs. One extends
For the F54 model, locate both modular wiring plugs. One extends
For the F54 model, locate both modular wiring plugs. One extends
For the F54 model, locate both modular wiring plugs. One extends
For the F54 model, locate both modular wiring plugs. One extends
4.
fr
fr
om the mounting plate on bottom of fan body and one extends fr
om the mounting plate on bottom of fan body and one extends fr
om the mounting plate on bottom of fan body and one extends fr
om the mounting plate on bottom of fan body and one extends fr
om the mounting plate on bottom of fan body and one extends fr
om the mounting plate on bottom of fan body and one extends fr
the Switch Housing. Align the two plugs so the latch on the side of the
the Switch Housing.
the Switch Housing.
the Switch Housing.
Align the two plugs so the latch on the side of the
Align the two plugs so the latch on the side of the
Align the two plugs so the latch on the side of the
Align the two plugs so the latch on the side of the
Align the two plugs so the latch on the side of the
plugs will engage when pushed together
plugs will engage when pushed together
plugs will engage when pushed together
plugs will engage when pushed together
plugs will engage when pushed together
together until latched.
together until latched.
together until latched.
together until latched.
together until latched.
together until latched.
5.
Carefully push wir
efully push wires up into hub. For F52 type install new hub cover
efully push wir
efully push wir
es up into hub. For F52 type install new hub cover
es up into hub. For F52 type install new hub cover
es up into hub. For F52 type install new hub cover
es up into hub. For F52 type install new hub cover
es up into hub. For F52 type install new hub cover
es up into hub. For F52 type install new hub cover
es up into hub. For F52 type install new hub cover
and light kit using scr
and light kit using scr
and light kit using scr
and light kit using scr
and light kit using scr
ews removed earlier
hub and light kit using scr
hub and light kit using scr
hub and light kit using scr
hub and light kit using scr
ews removed earlier
Install bulbs.
Install bulbs.
6.
F54
Screws
E4
e in hub, using wire nuts.
. Push the two plugs firmly
. Push the two plugs firmly
emoved earlier
. For F54 type, attach new
. For F54 type, attach new
. For F54 type, attach new
. For F54 type, attach new
emoved earlier
.
Remove
DLK Light Kit will only fit the following fans:
Fresco
Old Madrid
Constantina
Crescent
1. To remove switch housing hub from fan, unscrew one screw and loosen other 2
from the side of the switch housing hub (as shown in Diagram A below).
2. Gently twist switch housing hub counterclockwise and pull down carefully and
Remove
unplug.
4. Remove 3 screws from inside switch housing hub to remove switch housing hub
cover. (See Diagram B)
5. Carefully thread wires from fitter through the center hole in the switch housing
hub. At this point attach light kit into switch housing hub by screwing the three
screws back through the switch housing hub and light kit.
6. Attach white wire from light kit to white wire in switch housing hub, using wire
nuts. Next, attach black wire from light kit to blue wire in switch housing hub.
7. Locate both modular wiring plugs. One extends from the mounting plate on
om
bottom of fan body and one extends from the switch housing hub. Align the two
plugs so the latch on the side of the plugs will engage when pushed together. Push
the two plugs firmly together until latched.
8. Carefully push wires up into switch housing hub and replace switch housing
hub cover using screw removed earlier and tightening all three screws to secure
light kit in place.
E5
DIAGRAM A
DIAGRAM B
Publicidad
