Publicidad
Idiomas disponibles
Idiomas disponibles
Attention: Please make sure that the safety hook is LOCKED while grilling or moving. DO NOT
attempt to twist or pull the safety hook while using this unit.
7. Remove the screw from the trolley tube (III) first. Then mount the standpipe (G1) on the trolley tube (II)
and mount the standpipe (G2) on the trolley tube (II). There is a positioning hole (IV) on the standpipe
(G2), which secures G1 and G2 to each other with screws. Please fasten the standpipe (G and G2)
firmly to the trolley using screws and nuts (see figure 7).
8. Place the key-shaped bottom of the unit (h) on the standpipe (g). Attach the underside of the base to
the positioning hole (IV). When removing the base from the standpipe (g), slightly step onto the support
tube (I), hold the base handles and remove them (see figure 8).
9. Place the grease collecting bowl (j) in the slot of the bowl-shaped base (h). To secure it properly, make
sure that the hole on the grease collecting bowl matches the hole in the middle of the bowl-shaped base
(tip: The bowl can be filled with water to make it easier to clean). To remove the grease collecting bowl,
gently press lightly on the bottom (see figure 9).
Attention: The capacity of the grease collecting bowl is 0.3 L. Please pour out the fat when it's
full. The surface of the bowl is hot. Please do not touch the bowl during grilling.
10. Place the grill plate (K) on the bottom of the appliance (H). First, insert the socket (L) of the grill plate
into the hole (M) of the base. Please place the grill plate horizontally on the base of the appliance. To
remove the grill plate, hold the right side of the plate up and remove the connecting socket (L) from the
hole (M). Before removing the grill plate, make sure that it is completely cooled and not in use (see
figure 10).
Attention: Please use the lid handle to close or open the cover. Please note that the cover is hot
during grilling.
11. Please insert the removable thermostat with its cord (s) into the power socket (L). When removing the
thermostat, hold the handle of the base to prevent it from tipping over inadvertently (see figure 11).
Attention: Please be careful. Do not trip over the power cord when the unit is in use. Always
unplug the power cord after use.
12. Insert the thermometer (T) into the hole on the hood and fix it from the inside of the hood with the nut
(N) (see figure 12).
13. Please mount the upper cover. To do this, hold the cover handle (p) and place the metal hinges (O) into
the mounting holes (Q) of the base. When removing the upper cover, please open the cover and tilt it
up to 45° between the cover and the grill plate and detach the metal hinges (o) from the mounting holes
(Q) (see figure 13).
14. Since the upper cover is removable, it is more convenient for use and cleaning (see figure 14).
Attention: To close or open the cover, always use the lid handle. Note that the hood becomes
hot during the grilling process.
15. When moving the folded trolley or when not in use, please lock the cover with the buckle and make sure
that the belt hook (U) locks the tube (see figure 15).
Components of BBQ-9479
T. Thermometer
1. Handle
2. Upper cover
3. Grill plate
4. Grease collecting bowl
5. Base of appliance
6. Spice rack
7. Upper tube
8. Decoration
9. Lower tube
(The corresponding pictures can be found in the front of this manual.)
Installation of BBQ-9479
1. Install the stand feet (10A) into the stand base (10B) until you hear a "click" (see figure 1).
2. To fix the stand, place the disk (16) on the stand and tighten it with the screws (17) provided (figure 2).
3. Screw half of the threaded rod (a) into the lower tube (9). Then place the decorative ring (8) on the
threaded rod (a) and connect the upper tube (7) to the threaded rod (a) (see figure 3).
4. Connect the stand feet (10) to the lower tube (9) to form the complete grill stand (the grill can be used
with or without stand) (see figure 4).
5. Install the screw (b) on the upper tube (7) and place the spice rack (6) on top. (Please make sure that
the compartment is also fixed) (see figure 5).
6. Place the appliance's base (5) on the grill (make sure that the grill is placed on a dry, flat and stable
surface) (see figure 6).
7. Place the grease collecting bowl (4) into the provided holder of the base (5). Fasten the opening of the
grease collecting bowl with a screw (fill the bowl with a little water to make it easier to clean) (figure 7).
8. Place the grill plate (3) on the base (5). First, insert the socket (15) into the connection socket (12)
10 A. Stand feet
10 B. Stand base
11. Handle
12. Connection socket
13. Removable thermostat with cord
14. Indicating light
15. Socket
16. Disk
17. Screws
Publicidad
