Add Engine Oil - Troy-Bilt 030247-I Instrucciones De Uso

Section 3: Assembly
BEFORE STARTING THE
ENGINE
Add Engine Oil
CAUTION!
Any
attempt to crank or start the engine
before i[ has been properly serviced with the
recommended oil may resuI[ in an engine failure.
I. Place generator on a flat, level surface.
2. Clean area around oil fill and remove yellow oil fill cap.
NOTE: See the section "Oil" on page 17 1:o review oil
recommendations.Verify provided oil bo[de is correct
viscosity for current ambien[ [emperature.
3. Using oil funnel (optional), slowly pour conten1:s of
provided oil bottle into oil fill opening.
4. Replace oil fill cap and fully dgh[en.
Add Fuel
All fuel is no1: 1:he same. If a smri:ing or performance
problem is encountered immedia1:ely after new fuel has
been used, 1:ry ano1:her service s1:a1:ion or change brands.
NOTE:This engine is cer1:ified 1:o opera1:e on gasoline.
Exhaus1: Emissions Con1:rol Sys1:em: EM (Engine JVlodificadons
WARN I N G
WHEN ADDING FUEL
Turn generator OFF and let it cool at least 2 minutes before
removing fuel cap. Loosen cap slowly to relieve pressure in _nk.
Fill fuel tank outdoors.
DO NOT overfill tank.Allow space for fuel expansion.
Wait for spilled fuel to evaporate before starting engine.
Keep fuel away from sparks, open flames, pilot lights, heat, and
other ignition sources.
DO NOT light a cigarette or smoke.
Type of Fuel
I. Always use clean, fresh, UNLEADED gasoline wi1:h a
minimum of 87 octane/87 AKI
(91 RON).
DO NOT
mix oil wi1:h fuel. DO NOT modify 1:he engine fuel
sys1:em or carbure1:or 1:o run on al1:ernadve fuels.
NOTE: Fuel wi1:h up 1:o 10% el:hanoi (gasohol) or up 1:o
15% IViTBE (me1:hyl 1:erdary bu1:yl el:her), is acceptable.
iMPORTANT: Use of any fuel o1:her 1:han 1:hose
approved
above wiii void warranty. Some areas require 1:ha1:fuel
pumps be marked if 1:he fuel contains alcohols or el:hers. If
you are no1: sure if your fuel con1:ains alcohol or el:hers 1:ha1:
are differen1: 1:han 1:hose approved above, 1:hen check wi1:h
1:he service s1:adon opera1:or.
2. Clean area around fuel fiii cap, remove cap.
3. Slowly add unleaded gasoline 1:o fuel tank. Be careful
no1: 1:o overfill.Allow a1: leas1: 1.5" of tank space for fuel
expansion, as shown in Figure 3.
" - - D. •
4. Install fuel cap and ie1: any spilled fuel evapora1:e before
sl:ard ng engine.
To avoid engine performance issues, 1:he fuel sys1:em should
be 1:rea1:ed wi1:h a fuel preserver or empded before s1:orage
of 30 days or longer.To pro1:ec1: 1:he fuel sys1:em from gum
formation, use Brigs & S1:ra1:1:on FRESH START TM fuel
s1:abiiizer plus. if fuel preserver is no1: used, drain 1:he fuel
tank, s1:ar1:1:he engine and le1: i1: run undl 1:he fuel lines and
carbure1:or are emp1:y. Use fresh fuel nex1: season. See
"S1:orage" on page 20 for additional information.
NEVER use engine or carbure1:or cleaner produc1:s in 1:he
fuel tank as permanen1: damage may occur.
High=altitude use
Operation a1: high ald1:ude (over 5,000 fee1:), may require a
high-ald1:ude carbure1:or je1: I<11: 1:o improve performance and
decrease fuel consumption. See your local au1:horized Bri_gs
& S1:ra1:1:ondealer for more information.
O