Kärcher WD 3 Manual De Instrucciones página 13

Ocultar thumbs Ver también para WD 3:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 30
Recommendation: In order to vacuum the floor, attach
the handle to the suction hose.
Removable handle
Illustration
 Connect the handle with the suction hose until it
snaps in place.
Illustration
 To remove the handle from the suction hose, press
the notch using your thumb and pull off the handle.
Note: Due to removing the handle, accessories can be
directly attached to the suction hose.
Recommendation: In order to vacuum the floor, attach
the handle to the suction hose.
See position 13.
Suction tubes 2 x 0.5 m
Illustration
 Put both suction tubes together and connect them
with the handle.
Crevice nozzle
 For edges, joints, heaters and hard to reach loca-
tions.
Floor nozzle
(with inserts)
Illustration
 Note: For vacuuming dry dirt or water off the floor -
always work with the insert (brush strip and rubber
lip) in the floor nozzle.
Adapter
Illustration
 To connect the suction hose with an electric tool
 Adapt the adapter to the connection diameter of the
electric tool using a knife if necessary.
Operation
ATTENTION
Always work with an inserted cartridge filter during wet
as well as dry vacuum cleaning!
Before Startup
Illustration
 Mount loose parts delivered with appliance prior to
start-up.
Start up
Illustration
 Connect accessories.
Illustration
 Plug in the mains plug.
Illustration
 Turn on the machine.
Dry vacuum cleaning
ATTENTION
Check the filter for damage prior to installation and re-
place as necessary.
Work with a dry cartridge filter only!
Illustration
 Recommendation: To vacuum fine dust, use the
filter bag.
Information filter bag
The filling level of the filter bag depends on the dirt
that is sucked in.
The filter bag needs to be replaced more frequently
while sucking in fine dust, sand, etc.
Clogged filter bags can burst - therefore make sure
to replace the filter bag in a timely manner!
ATTENTION
Vacuum cold ashes only when using a pre-filter.
Order no. basic design: 2.863-139.0, premium design:
2.863-161.0.
Wet vacuum cleaning
 For vacuuming up moisture or liquids pay attention
to the correct floor nozzle insert and connect the
corresponding accessories.
ATTENTION
Do not use a filter bag!
Note: If the container is full, a float closes the suction
opening, and the appliance works at a higher speed.
Switch off the appliance immediately, and empty the
container.
Working with electrical power tools
Illustration
 Adapt the adapter to the connection diameter of the
electric tool using a knife if necessary.
 Connect the adapter to the handle of the suction
hose and connect it to the electric tool connection.
Connect the mains plug of the electric power tool to
the vacuum cleaner.
Illustration
 Switch the vacuum cleaner to Position II and start
working.
Note: As soon as the electric tool is switched on, the
suction turbine starts with a 0.5 second delay. If the
electric tool is switched off, the suction turbine contin-
ues to run for approx. 5 seconds in order to vacuum up
the remaining dirt in the suction hose.
Cleaning hard to reach locations or, where vacuuming
is not possible, like leaves from a gravel bed.
Illustration
 Connect the suction hose to the blower connection,
this will activate the blower function.
Interrupting operation
 Turn off the appliance.
Illustration
 Hook the floor nozzle into the parking position.
– 8
EN
Blowing function
13

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Wd 3 premiumWd 3 pWd 3 p premium

Tabla de contenido