Cold Laminating - Q-Connect QCLA3 Manual De Instrucciones

1 Inlet
2 Outlet
3 Power button
4 Power LED (red when ON)
5 Ready LED (green when ready)
6 Temperature control dial
7 Roller release button
8 Electric plug
9 Power socket
GeNeRAL SAfeGuARDS
Failure to comply with any of the following safety precautions
may result in serious injury, fire or electrocution. Keep out of the
reach of children. Unauthorised maintenance is not allowed. Do
not allow liquid to get into the machine.
Do not insert any foreign object or put your fingers or hand inside.
This machine is heat emitting, do not leave
unattended during operation. Allow enough space behind the
laminator to ensure free clearance of the laminated object and
prevent blockage.
OpeRATING INSTRuCTIONS HOT
LAMINATING
1 Insert the electric plug (8) into the power socket (9).
2 Turn on the laminator by pressing the power button (3)
towards the HOT direction. The power LED (4) will glow red.
3 The green ready LED (5) will glow when the laminator is ready
for lamination.
4 Adjust the temperature by turning the temperature control
dial (6) so that the pointer is pointing to the corresponding
temperature setting
Temperature reference table
Item to be laminated 80µm
Newspaper 1-2
Copying paper 2-3
Photograph 4-5
5 Prepare the item to be laminated. Insert the item in between
the laminating pouch and push it to the sealed end of the
pouch. WE RECOMMEND TO USE Q-CONNECT LAMINATING
POUCHES.
6 Insert the sealed end of the pouch straight into the laminator
through the inlet (1). Once the pouch is engaged by the roller,
it will be rolled into the laminator automatically.
7 Remove the laminated item from the outlet (2).
8 After use, turn off the laminator by pressing the power button
(4).

COLD LAMINATING

1 Insert the electric plug (8) into the power socket (9).
2 Turn on the laminator by pressing the power button (3)
towards the COLD direction. The power LED (4) will glow red.
3 The green ready LED (5) will glow immediately.
4 Prepare the item to be laminated. Open the pouch and insert
the item in between the laminating pouch so that the part
with the protective paper is on top.
100µm 125µm 150µm
2-3 4-5 6-7
3-4 4-5 6-7
5-6 6-7 7
3
5 Peel off the first few centimeters of the protective paper and
insert the closed end of the pouch centrally into the laminator
through the inlet (1). Once the pouch is engaged by the roller,
carefully remove the protective paper as the pouch is rolled
into the laminator.
6 Remove the finished product from the outlet (2). Do not
attempt to pull the pouch out before the laminating process is
completed.
7 After use, turn off the laminator by pressing the power button
(4).
ReMOvING jAMMeD LAMINATING
pOuCHeS
If the laminating pouch is jammed inside the laminator during the
laminating process, press the roller release button (7) and pull the
jammed pouch out immediately.
After the jammed pouch is removed, release the roller release
button and continue with a fresh laminating pouch.
If the jammed pouch cannot be removed, turn off the laminator
and report to the dealer shop for assistance.
CLeANING THe LAMINATOR
After laminating several documents, adhesive material from the
pouch may accumulate inside the laminator. Please clean the
laminator regularly as follows:
1 Turn on the laminator by pressing the power button (3)
towards the HOT direction until the ready LED (4) glows.
2 Fold a sheet of fresh copying paper once at the middle and
insert with the folded end first through the laminator. Repeat
the same procedure for 3 - 5 times.
CLeANING THe bODy
1 Unplug the laminator.
2 Wipe with a soft cloth and a general-purpose household
cleaner.
SpeCIfICATIONS
Max. Laminating width: 330mm.
Laminating speed: 252mm/min.
Max. Laminating Thickness: 0,6mm.
Pouch film Thickness: 75 - 150 micron per side.
Jammed paper release: roller release button.
2 rollers.
Pre-heat time: 5 minutes.
Carrier free.
Voltage: 220V.
Consumption power: 435 W.
Current: 1,9 A.
Weight: 2,9 kg.
Dimensions: 466 x 189 x 121mm.
Body Material: ABS.
t