Black+Decker GK1740 Manual De Instrucciones página 21

b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following
symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........ Volts
n .......
0
A ........ Amperes
Hertz
...... Class II
Watts
....
minutes
..... Alternating
....
Current
..... Direct
.../min..
Current
No-Load
Speed
8. En la herramienta aparecen los siguientes
símbolos de advertencia:
Warning
Read the manual prior to
operation.
Always wear ear and eye
protection.
Do not expose the
appliance to rain or high
humidity
FEATURES (Fig. A)
1. On/off switch
2. Lock-off button
3. Oil cap
4. Front guard/chain brake assembly
5. Chain tension adjustment screw
6. Chain
7. Guide bar
8. Chain sheath
9. Chain cover knob
10. Chain cover assembly
11. Oil level indicator
ADDITIONAL SAFETY INSTRUCTIONS
f Keep all parts of the body aw ay from the saw
chain when the chainsaw is operating. Before
you start the chainsaw, make sure the saw
chain is not contacting anything. A moment of
inattention while operating the chainsaw may cause
entanglement of your clothing or body with the chainsaw.
f Always hold the chainsaw wi th your right hand on
the rear handle and your left hand on the front
handle. Holding the chainsaw with the reversed hand
configuration increases the risk of personal injury and
should never be done.
f Wear safety glasses and he aring protection.
Further protective equipment for head, hands,
legs and feet is recommended. Adequate protective
clothing will reduce personal injury by flying debris or
accidental contact with the saw chain.
f Do not operate a chainsaw in a tree. Operation of a
chainsaw while up in a tree may result in personal
Construction
injury.
Earthing
f Always keep proper footin g and operate the
Terminal
chainsaw only when standing on fixed, secure
Safety Alert
Symbol and level surface. Slippery or unstable surfaces such
as ladders may cause aloss of balance or control of
Revolutions
or Recipro-
the chainsaw.
cation per
minute
f When cutting a limb that is under tension be alert
for spring back. When the tension in the wood fibres
ENGLISH • 21
Remove the plug from the
socket if the mains cable is
damaged or before
maintenance.
The noise from this product
can exceed 85 dB(A).
FOR THE CHAINSAW
Check the chain
tension after every
10 minutes of use.
Adjust back to a
clearance of 3 mm.