Tabla de contenido
Publicidad
2.
Use dust masks.
3.
Use earplugs to keep your ears noise-free while
working.
4.
Check for the proper handle adjustment.
5.
The tool becomes very hot during operation.
6.
Safe operation depends on one's work posture.
7.
When working in an elevated location, pay attention
to objects and persons below.
8.
Wear protective shoes to protect your feet.
Failure
to
follow
safety
recommendations
instructions may result in serious injuries or death!
III. TECHNICAL SPECIFICATIONS
Product name
Diamond drilling machine
Model
MSW-
MSW-
MSW-
DDM230
DDM205
DDM152
Rated
230/50
voltage [~V]/
Frequency[Hz]
Rated power [W]
4080
3900
2880
Weight [kg]
21
20,5
12
Water connection
½
diameter ['']
Maximum
570
580
1200
rotational speed
(without load)
[rpm]
Core drill
1 ¼"
attachment
diameter
Core drill
15 – 230
15 – 205
15 – 152
diameter [mm]
Product name
Diamond drilling machine
Model
MSW-DDM255
MSW-DDM132
Rated
230/50
voltage [~V]/
Frequency[Hz]
Rated power [W]
4350
1980
Weight [kg]
22
10
Water connection
½
diameter ['']
Maximum
580
1200
rotational speed
(without load)
[rpm]
Core drill
1 ¼"
attachment
diameter
Core drill
15 – 255
15 – 132
diameter [mm]
8
IV. APPLICATIONS
The diamond core drill is designed to drill pass-through
and not pass-through holes in mineral construction
materials such as concrete, all types of walls, asphalt, all
types of screed, natural stone, with the use of standard
diamond tipped core drills, wet drilling and using a stand.
V. BEFORE FIRST USE
1.
Power source.
Ensure that the power source which is utilized
and
conforms to the power requirements specified on
the product name.
2.
Power switch.
Ensure that the power switch is in the OFF position.
If the plug is connected to a power receptacle while
the power switch is in the ON position, serious
accidents can occur.
3.
Extension cord.
When the work area has no power source, use an
extension cord of sufficient thickness and rated
capacity. The extension cord should be kept as short
as possible.
VI. DESCRIPTION OF THE DEVICE
MSW-DDM230 / MSW-DDM205 / MSW-DDM132
4
4
3
5
6
1.
spindle
8
7
2.
coolant valve
3.
motor
4.
motor carbon brushes
cover
2
1
5.
ON/OFF switch
6.
device height adjustment
9
handle
7.
lever for raising/
10
lowering the device
8.
handle
9.
guide rail
10.
attachment screws
11
11.
base
Open the coolant valve and place the hose end in the work
area. Turn on the device. Use lever for raising / lowering the
device to adjust device height. Upon completing work, close
the coolant valve, raise the device and turn it off.
ATTENTION! Ensure that the core drill does not snag in the
work-piece during operation.
MSW-DDM152
5
1.
attachment screws
4
2.
ON/OFF trigger
3.
handle
3
6
4.
ON/OFF trigger lock
2
7
button
5.
motor carbon brushes
cover
8
6.
coolant valve
7.
lever for raising/
lowering the device
9
1
8.
spindle
9.
base
Rev. 27.03.2018
Open the coolant valve and place the hose end in the
work area. Press and hold the ON/OFF trigger (2) to start
the device, release the trigger to stop the device. For
continuous operation, press and hold the ON/OFF trigger
(2), then press the lock button (4). The device will continue
operating after the ON/OFF trigger is released. Use lever
for raising / lowering the device to adjust device height.
Upon completing work, close the coolant valve, raise the
device and turn it off by releasing the trigger (2)
ATTENTION! Ensure that the core drill does not snag in the
work-piece during operation.
MSW-DDM255
12
1
11
2
3
10
8
4
9
5
A
B
6
C
7
1.
control panel
A – revs adjuster
B – on button
C – off button
2.
device attachment to guide rail unit
3.
attachment screw
4.
lever for raising/lowering the device
5.
guide rail for raising / lowering the device
6.
attachment screws
7.
base
8.
coolant valve
9.
spindle
10.
device
11.
motor
12.
motor carbon brushes cover
Open the coolant valve and put the pipe output in
the work area. Before turning it off, make sure that
the minimal rotation speed range is selected. Turn
the device on via the built-in switch, adjust the speed
control to the rotation speed of the required task and
adjust the height of the device with the lever. After
having successfully used it, turn off the cooling water
valve, hold the device upwards, adjust the rotation
speed to the smallest value and turn the device off
via the switch. ATTENTION! When working, make
sure that the core drills are not in the workpiece.
VII. ASSEMBLING THE DEVICE
1.
Place the device on a stable and level surface,
use attachment anchors to mount the device
to the surface:
2.
Place device base on the surface.
3.
Mark the position of attachment holes.
Rev. 27.03.2018
4.
Drill holes on the surface at the market positions.
5.
Insert anchors into the drilled holes.
6.
Align the holes in device bases with drilled holes
and tighten the attachment screws.
7.
Level the device.
VIII. REPLACING CARBON BRUSHES
When the device is operated, carbon brushes steadily wear
out. When the insulation tip integrated inside the brush gets
revealed and touches the commutator it will trip the engine
automatically. When this happens, both brushes must be
replaced with new brushes of the same type. Inspect the
carbon brushes after approx. 300 working hours.
Attention! Before commencing carbon-brush replacement,
make sure the device is switched off and the power cord
is unplugged.
Replacing the carbon brushes:
Unscrew the screw securing the carbon brushes on the side
of the device housing:
Remove worn out carbon brush, insert new brush and
tighten the screw. Replace the carbon brush on the other
side of the housing in an analogous manner.
IX. ASSEMBLY/DISASSEMBLY OF THE
DEVICE'S ELEMENTS
•
Device height adjustment handle assembly:
Remove the screw from the handle bracket, insert the
bracket into the device attachment, align holes:
Tighten the screw. When tightening make sure the screw
goes all the way through.
•
Coolant feed hose assembly:
Slide hose end over device coolant feed valve:
Once on, use a hose clamp to secure the hose in place.
•
Bracket assembly:
Align the bracket with the guide rail and secure it to the
rail using two bolts.
•
Mounting a core drill on the device.
To mount a core drill on the spindle, screw it on clockwise.
9
Publicidad
Tabla de contenido
