Technical Data - Vetus ALEXANDER III Manual De Manejo Y Instrucciones De Instalación

Solenoid Switch
The engine of the anchor windlass should be set in operation
by means of a solenoid switch, the contact ratings of which are
suited for the engine supply.
If only 1 rotating direction of the electric motor is desired
(only for the 'hauling in' of the chain by means of the electric
motor), it is sufficient to use a solenoid switch with 1 normally
open contact.
If 2 rotating directions of the electric motor are desired (both
for the hauling in of the chain and the letting go of the chain
by means of the electric motor), one must apply two solenoid
switches with each 1 normally open contact.
Connect the engine and the relay as indicated in one of the
schemes on page 26.
Position the solenoid switch preferably as close as possible to
the anchor windlass.
Never mount the solenoid switch in the chain locker.
The two motor relays must never be switched on at the same
time. There is a danger of this occurring when two sepa-
rate switches are used for hauling in and letting go. If that
is the case, 2 extra relays should be installed. See drawing.
We can also supply:
Anchor chain
Art. code: Article description:
CHAIN08.. Anchor chain 8 mm DIN 766
(calibrated and galvanised)
CHAIN10.. Anchor chain 10 mm DIN 766
(calibrated and galvanised)
CHAIN08SS Anchor chain 8 mm DIN 766, per metre
(stainless steel)
CHAIN10SS Anchor chain 10 mm DIN 766, per metre
(stainless steel)
Bow rollers
Art. code: Article description:
ASTERIX Bow roller type Asterix, suitable for rope and
chain up to 8 mm (5/16")
OBELIX Bow roller type Obelix, suitable for rope and
chain up to 13 mm (1/2")
POLLY Bow roller type Polly, suitable for rope and
chain up to 8 mm (5/16")
FRANCIS Bow roller type Francis, suitable for rope
and chain up to 8 mm (5/16")
ED Bow roller type Ed, suitable for rope and
chain up to 13 mm (1/2")
Electric anchor windlass ALEXANDER III
Note!

Technical data

Different data for the 24 V model are printed in italics.
Electric motor
Type : Direct current series motor
Voltage : 12 V DC
Rated current : 10 A
Rated output : nominal 1000 W; Maximum 1500 W
No. revolutions : 3100 rpm
(with nominal output)
Rating : S2 - 10 min.
Protection : Class IP 
Transmission
Gears : worm wheel, ratio: 60:1
Lubrication : grease, Agip GRMU/EP 0
Gipsy
For the chain : 8 mm, in accordance with DIN766/ISO565
calibrated, or
10 mm, in accordance with DIN766
calibrated
Lifting power : nominal 330 N (770 lbf)
max. 900 N (1100 lbf)
Chain velocity : 26 m/min at 25 N (55 lbf) load
13.5 m/min at 330 N (770 lbf) load
Weight
: 20 kg ( lbs)
Solenoid Switch
For the 'hauling in' of the chain we can supply the following:
- remote controle consisting of:
1 solenoid switch (relays) single pole, normally open
12 V version Vetus art. code: AFST1512S
2 V version Vetus art. code: AFST32S
For 'hauling in and letting go' twice the remote controle as
specified under 'hauling in' can be applied.
We can furthermore supply a control box for manual use, with a
coiled cord to be used in combination with the aforesaid sole-
noid switches. Vetus art. code: RECON
ENGLISH
24 V DC
70 A
3200 rpm
9
060113.05