Auto-Off Timer; General Maintenance - Makita DCF203 Manual De Instrucciones

Oscillating the fan head
CAUTION:
When oscillating the fan head, keep
obstacles clear of the moving range of the fan head.
The cordless fan may be pushed and fall by the
oscillation.
CAUTION:
Do not stop the oscillation by holding
the fan head. Always press the oscillation button to
stop.
Press the oscillation button to oscillate the fan head.
Press the button again to stop the oscillation. The fan
head begins to oscillate from the current position when
the oscillation button is pressed. The fan head oscillates
in the range of 90-degrees.
► Fig.7: 1. Oscillation button
NOTE: Depending on the fan head position, the fan
head may not oscillate soon after the oscillation but-
ton is pressed because of the oscillation mechanism.

Auto-off timer

Press the auto-off timer button while the fan is running.
The duration to activate auto-off timer changes every
time you press the button (1 hour / 2 hours / 4 hours /
off). The number under each auto-off timer indicator
shows the remaining hour(s) to turn off the fan. The
auto-off timer indicator will turn off with time.
► Fig.8: 1. Auto-off timer button
NOTE: Depending on the battery cartridge type and
its remaining capacity, the auto-off timer may be
activated earlier than the set time.
Using AC adaptor
WARNING:
Never use the appliance when the
cord or plug is damaged.
WARNING:
Do not handle the plug with wet or
greasy hand.
WARNING:
Do not leave the AC adaptor discon-
nected from the appliance while the power is supplied
from the mains. Small children may put the live plug
in their mouth and cause injury.
WARNING:
Do not put the live plug or cord into
your mouth. Doing so might cause an electric shock.
Insert the 15V DC plug of AC adaptor into the 15V DC
socket, and then plug the AC pins into a main power
supply. Make sure that the voltage rating of the main
power supply corresponds with that of the adaptor.
► Fig.9
NOTE: After the AC adaptor is connected, the appli-
ance may take 3–5 seconds to start.
NOTE: The adaptor might creak while using it for the
power supply. This doesn't affect normal use.
NOTE: Even operating in DC power mode, the appli-
ance is automatically changed into AC power mode
when plugged in.
NOTE: When the cordless fan switches the power
mode from DC to AC, and vice versa, the wind speed
may change temporarily.
NOTE: The AC adaptor does not charge the battery
inserted to the appliance.
MAINTENANCE
CAUTION:
Always be sure that the appliance
is switched off, unplugged, and the battery car-
tridge is removed before attempting to perform
inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.

General maintenance

After the appliance is cooled, use clean clothes to
remove dirt, dust, oil, grease etc.
WARNING:
Authorized Service Center.
Fan Cleaning
CAUTION:
Ensure that the fan is switched off
from the supply mains before removing the guard.
When cleaning the inside of fan-cover, remove the fan-
cover by following way.
1. Loosen the screw located on the back of the
fan-cover.
► Fig.10: 1. Screw
2. Turn the fan-cover counterclockwise, and remove
the fan-cover when the markings are aligned as
illustrated.
► Fig.11: 1. Marking
► Fig.12
Wipe off the fan and fan-cover using a cloth dampened
in soapy water.
To attach the fan-cover, follow the removing procedure
in reverse. When attaching the fan-cover, make sure
that the fan-cover is locked with a click.
10 ENGLISH
All parts should be replaced at an