Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Item Description
These terminals are used to connect the WSI box to a power
source.
If you want to use the WSI box with other Nexus products, see
the Nexus device owner's manual.
This connector fits only one way. Match the wire colors to the
terminal blocks before inserting the connector.
This connects to either NEXUS port on the GND 10 bridge.
Item
Description
WSI box
WSI cable
GND 10 bridge
NMEA 2000 network
Configuring the Wind Transducer
Before you can configure the wind transducer, it must be
connected through a GND 10 to a NMEA 2000 network with a
Garmin marine instrument, such as a GMI
marine instrument owner's manual for more information on
configuring NMEA 2000 devices.
1
On the marine instrument, go to the NMEA 2000 settings.
2
Select the name of the device (GND 10) to configure.
Adjusting the Orientation
You should adjust this setting if the sensor does not face the
front of the boat, exactly parallel to the center line.
1
On the marine instrument, from the NMEA 2000 settings,
select the device name (GND 10).
2
Select Wind Angle Offset.
3
Estimate the angle, in degrees clockwise around the mast, by
which the sensor points away from the center of the front of
the boat:
4
4
5
Adjusting the Wind Angle Filter
You should adjust this setting to change the responsiveness of
the display to changes in the wind direction.
1
2
3
4
Adjusting the Wind Speed Filter
You should adjust this setting to change the responsiveness of
the display to changes in the wind speed.
1
2
3
4
Maintenance and Storage
• If needed, use a mild soap solution to clean the wind
• It is recommended to remove the wind transducer and store it
• It is recommended to remove the WSI and store it in a dry
• When storing the wind transducer, it is best to store it in a
20. Refer to the
™
• If you store the wind transducer in a dark location, it is
Pairing the Wind Transducer with the WSI
Before you can pair the wind transducer with the WSI, you must
have a Garmin marine instrument, such as a GMI 20 connected
to the same NMEA 2000 network as the GND 10.
This wind transducer is paired with the WSI at the factory. You
must pair the wind transducer with the WSI only if you replace
the device.
• If the sensor is facing starboard, the angle should be
between 1 and 180 degrees.
• If the sensor is facing port, the angle should be between
181 and 360 degrees.
Select the angle observed in step 3.
Select Done.
On the marine instrument, from the NMEA 2000 settings,
select the device name (GND 10).
Select Wind Angle Filter.
Select an option:
• Select Off to turn off the filter and make the display the
most responsive to changes in the wind angle.
• Select On and adjust the value. Select a higher number to
increase the responsiveness of the display to changes in
the wind angle, or select a lower number to decrease the
responsiveness.
• Select Auto to automatically adjust the filter settings
based on wind conditions.
Select Done.
On the marine instrument, from the NMEA 2000 settings,
select the device name (GND 10).
Select Wind Speed Filter.
Select an option:
• Select Off to turn off the filter and make the display the
most responsive to changes in the wind speed.
• Select On and adjust the value. Select a higher number to
increase the responsiveness of the display to changes in
the wind speed, or select a lower number to decrease the
responsiveness.
• Select Auto to automatically adjust the filter settings
based on wind conditions.
Select Done.
transducer, and rinse it with water. Do not use detergents or
high-pressure water.
in a dry location if it will not be used for long periods of time.
location if it will not be used for long periods of time.
location where it is exposed to light. This maintains the
battery charge in the device.
recommended to replace the battery at the beginning of each
season. Replacement batteries are available from your local
Garmin dealer, or from www.garmin.com.
Installation Instructions
Publicidad
Tabla de contenido
