Imesa IM9 Instruciones De Utilizo página 14

E021001C
8. cold rinse with softner (3')
9. spin 1000 rpm (3') *:
10. anti-wrinkle rolling
PROGRAMME 2
1. Pre-wash 35° C (3')
2. spin 500 rpm (1')
3. wash 60° C (5')
4. rinse cold (3')
5. spin 500 rpm (1')
6. rinse cold (3')
7. spin 500 rpm (1')
8. cold rinse with softner (3')
9. spin 1000 rpm (3') *:
10. anti-wrinkle rolling
PROGRAMME 3
1. Pre-wash 35° C (3')
2. spin 500 rpm (1')
3. wash 40° C (5')
4. rinse cold (3')
5. spin 500 rpm (1')
6. rinse cold (3')
7. spin 500 rpm (1')
8. cold rinse with softner (3')
9. spin 1000 rpm (3') *:
10. anti-wrinkle rolling
PROGRAMME 4
1. Cold pre-wash (3')
2. Wash 30° C (5')
3. Cold rinse (3')
4. Spin 500 rpm (1')
5. Cold rince (3')
6. Spin 500 rpm (1')
7. Cold rinse with softner (3')
8. Spin 1000 rpm (3') *:
9. Anti-wrinkle rolling
PROGRAMME 5 (WOOL)
1. Cold pre-wash (3')
2. wash 30° C (3')
3. Cold rinse (3')
4. Cold rince (3')
5. Cold rinse with softner (3')
6. Spin 450 rpm (1')
7. Anti-wrinkle rolling
PROGRAMME 6 (COLD)
1. Cold pre-wash (3')
2. Spin 500 rpm (1')
3. Cold wash (3')
4. Cold rinse (3')
5. Spin 500 rpm (1')
6. Cold rinse (3')
7. Spin 500 rpm (1')
8. Cold rinse (3')
9. Spin 1000 rpm (3') *:
10. Anti-wrinkle rolling
*:for the low spin washing machines, also the high
spin ones, are at 500 rpm.
17. DISPLAY MESSAGES
In the scheme below we point out the messages,
that can appear on the display of IM9. We suggest
you to provide for the maintenance of the machine
only applying
technicians.
MESSAGGE
AL 1
AL 2
AL 3
AL 4
AL 5
AL 6
AL 10
bL
COOLING
DETERGENT
END TEMP
END H2O
14
to authorised and
MEANING
It appears in
overheating of the
Please call the
Assistance Service
Will be displayed if door opened
during programmes execution
Call assistance service.
It appears in case of damage of
the temperature probe
Will be displayed when max
allowed water loading time is
over. Call for assistance.
Will be displayed when max
allowed water outlet time is
over. Call for assistance.
It appears only in coin op
versions: when a coin is fit-in, in
the coin.
It appears when one or more
panels of the machines are
open for maintenance (end of
perimetrical stroke, when it is
present).
It appears during the anti-
wrinkle rolling
immediately after
unbalance.
It appears during the cool-down
(par. 9).
It appears when the detergent
must be loaded; the display will
show it all the time when it is
possible to make this operation.
It appears when at programme
ending when the
temperature is higher
40° C. It disappears only when
the temperature is under this
limit.
It appears when
programme ending the water
level is higher than 5 cm. It
disappears when the water has
been completely unloaded.
07/10/02
qualified
case of
motor.
Technical
cycle,
one
water
than
at the