Configuration; Video Recording - Radiodetection SPX P340 flexiprobe Guia Del Usuario

Configuration

Once the system is correctly assembled and connected to a power source,
you may need to configure the controller's software.
Switch the On/Off switch to On.
After 5 seconds the SPX splash screen will be displayed for 5 seconds.
This will be followed by the welcome screen:
• Check that the date and time are correct and that the correct video
standard for your country (PAL or NTSC) is displayed.
• Check that the correct reel size is set.
• If a USB Flash Drive or CF card is present, check that the correct memory
parameters are displayed (if both a USB drive and CF card are present
then only the USB drive parameters will be displayed).
Press OK or Enter to continue.
If required you can set up the correct reel type, date, time and language
as follows:
To navigate through the system software use the keypad or keyboard
function and arrows keys. Use the
Use the and keys to scroll through the various options and press OK
to accept the selection.
Select the correct reel
Select "Menu" (F1 key) to go to the main menu screen, select "Set-up" and
press OK.
Select "Reel", press OK to continue to the Reel Setup Menu.
Use the or keys to select the correct reel length and type, press OK
to confirm your choice.
Press to exit the Reel Setup Menu.
Basic Controller Set-up
From the main Setup Menu, select "Controller" and press OK .
Select "Basic Settings" and press OK.
Select the setting you wish to edit and press OK or Enter.
Use the keyboard to modify Time or Date and use the
scroll through the various options.
Press OK to accept the new settings.
When all the required settings have been setup, press F6 to exit to the
top-level screen.
tFt Screen Settings
The screen brightness and contrast functions are available on the top
level screen.
Press BRI (F5) to set the Screen Brightness or CONTR (F6) to set the
Screen Contrast.
Use the and keys to set the desired value and press OK to accept
your settings.
key to return to the previous menu.
and keys to
8
Jobs
By entering information about your current session Client, Site and Survey
the P340 Controller will organize all your recordings (videos or photos)
USB
and observations in Jobs structures. This information will also be used to
generate the final detailed report (if required) by using FlexiSight manager.
Consult the operational manual for more details.
to start a new job:
Go to the Job browser: from the main Setup Menu, select "Jobs" and press
OK.
Press NEW (F1) and enter Client, Site and Survey details. Press START to start
the new job.
to resume or review an existing job:
Go to the Job browser: from the main Setup Menu, select "Jobs" and press
OK.
Use the or keys to select the Job you wish to resume or review and
press OK.
Press START (F1) to resume the job,
or:
use the and keys to select Job details or media (photos or videos),
press OK to review, edit or preview.
Recordings
NOte: Do not remove or install the removable storage device when the
system is powered and do not switch off the unit while recording. Failure
to comply may damage the removable storage device and /or recordings.
Formatting the removable storage device will delete all the files.
If you are using a USB flash drive device this will automatically be used to
store all your data (videos, photos and observations) even in the presence
of a compatible CF card.

Video recording

Press the key to start recording.
Enter job details if required:
• Review Client Name, Site Address and Survey Start and Finish Survey
references by pressing the
press OK again to accept the changes.
• On the keypad, press the
inspection.
Press the key to pause a recording, press the
recording.
Press the key to finish recording.
Press Fn and or to pan a zoomed video image.
Press or to zoom in or out.
Press the rotate keys or to rotate the video image.
To restore an altered image, simultaneously press both video effects keys
for example and .
and keys. Press OK to Edit and then
key again to start recording the
key or to resume
9