Putting Into Operation; Maintenance And Service; Accessories; Storage - Narex ASV 14-2A Instrucciones De Uso Originales

English
accumulators. The device then works intermittently or does
not work at all. It is necessary to reduce machine load or to
recharge the accumulator.
Accumulator storage
Store the accumulators in the fully charged state in a dry and dust-
free room at the ambient temperature ranging preferably from
5 °C to 40 °C. If you do not use the accumulators for a longer time
period, it is recommended to charge the accumulators fully once in
three months as a minimum!
Warning!!
The charger is not user serviceable. There are no user serviceable
parts inside the charger. Servicing at the closest Authorized Ser-
vice Center is required to avoid damage to static sensitive internal
components.
Always use correct battery pack (pack supplied with the tool or the
replacement pack recommended by the manufacturer, the compa-
ny Narex s.r.o.) Never install another battery pack type. It will ruin
your tool and may create a hazardous condition.

Putting into operation

Accumulator placing and removal
Insert the accumulator (1) from the rear power tool side into the
guide rail as far as the stop. By pulling the accumulator backwards
make sure that the accumulator is seated properly.
When removing the accumulator (1), press the accumulator
clamps (2) on both sides and by pulling the accumulator back-
wards take it out of the power tool.
Check of accumulator state
The power tool is equipped by the accumulator state indication
panel (9).
When the accumulator is seated in the power tool, press the indica-
tion switch (10a) on the accumulator state indication panel (9). The
indicator (10b) will light, depending on the residual accumulator
capacity (charging).
If the indicator state is LOW (discharged accumulator), take the
accumulator out of the machine and let it charge. Max. charging is
indicated by the HIGH indicator signal.
Switching-on
By depressing the operating push button (3) and by its holding
you can control speed smoothly. When depressing the push but-
ton switch (3) the LED indicator, serving for lighting the workplace
in front of the tool lamped in the chuck, will go on automatically.
Switching-off
By releasing the operating push button (3). Runout of the spindle
with the chuck is reduced by the activated brake.
Lower speed is suitable for guiding the bolt/screw to the material.
Higher speed is suitable for screwing the bolt/screw into the mate-
rial or for drilling into the material.
Attention!
Long-time use of variable rotating speed is not recommended as
its can result in operating push button damage.
Changed direction of rotation
Direction of rotation is changed by the change over switch of the
sense of rotation (4):
· By pushing from the right to the left – right run.
· By pushing from the left to the right – left run.
· Push button in the interposition – protection from uninten-
tional switching.
Attention!
If you wish to change position of the change over switch, check at
first that the operating push button is released.
Note:
During first use of the device and during the first change of the
sense of rotation a loud click can be heard. It is a normal phenome-
non which cannot be considered any problem.
18
Speed changing
Speed changing is carried out by the sliding switch (5).
1. low speed: move the switch towards the chuck
- the block letter "L" will appear
2. high speed: move the switch from the chuck
- the block letter "H" will appear
Torque setting
The necessary torque can be set by swiveling the adjusting ring (6)
towards the relevant symbol.
Screwing
Symbol 1 = min. torque
Symbol 20 = max. torque for screwing
Drilling
Symbol
= max. torque
Tool clamping and releasing
By swiveling the clamping chuck sleeve (8), you open and close
the clamping jaws, which the working tool (bit, bit holder, etc.) is
inserted into. The devices are equipped by automatic spindle arrest
(locking) facilitating tool replacement, by using one hand only in
the requested direction.

Maintenance and service

Instructions for device cleaning
Start the motor and blow impurities and dust out of the vent holes
of the device. Use protective goggles for this operation. Clean the
external plastic parts by a wet rag and mild detergent. Though
these parts are made of the materials resistant to solvents, NEVER
use any solvent.
Instructions for cleaning the charger
Attention! Risk of electric shock. Prior to start han-
dling the charger, disconnect the line plug from the
socket!
Impurities and dust can be removed from external charger surfaces
by a rag or a non-metal brush. Use neither water nor detergents.
Attention! With respect to protection from el. shock
and preservation of the class of protection, all mainte-
nance and service operations requesting jig saw case
removal must be performed by the authorized service centre
only!
The current list of authorized service centres can be found at our
website www.narex.cz, section "Service centres".

Accessories

The accessories recommended for use with this device are availa-
ble commercially in the shops with hand el. tools.

Storage

Packed appliance may be stored in dry, unheated storage place
with temperature not lower than -5 °C.
Unpacked appliance should be stored only in dry storage place
with temperature not lower than +5 °C with exclusion of all sudden
temperature changes.

Environmental protection

Power tools, accessories and packaging should be sorted for envi-
ronmental-friendly recy.
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electri-
cal and electronic equipment and its incorporation into national
law, power tools that are no longer suitable for must be separately
collected and sent for recovery in an environmental-friendly man-
ner.