Diamond VA10/R2 Manual De Installación E Instrucciones Para El Uso página 5

1) HANDLING AND TRANSPORT
The equipment is packed in a wooden crate (fig. A) which is suitable for lifting by
fork lifts or transpallette in order to avoid possible damages. The equipment must
be moved by qualified personnel. The wooden packing can be recycled, therefore
it has to be disposed in the special waste plan for recycling. It is advisable to use
a wooden board for any handling of the cabinet in order to avoid damages of the
structure (fig. B).
Carefully unpack the cabinet, paying attention so as not to damage it or
throw parts necessary for the assembling away, considering that inside
the cabinet you will fi nd the glasses and all the necessary assembling
parts (for example screws). During the handling of the cabinet to install
it on its place, the cabinet must be never pulled on its side ends.
2) COMPLAINTS
On receipt of the refrigerated equipment verify immediately if there are transport
damages. In case the unit is damaged in any way, notify immediately the driver and,
within 3 days, the shipping company by registered letter.
Every complaint must arrive at the manufacturer within 8 days from receipt of the
equipment. After this term the manufacturer will not take any responsibility.
3) IMPORTANT INSTRUCTIONS AND SUGGESTIONS
Before using the equipment it is important to read these instructions carefully
as improper use can be dangerous. Before connecting the refrigerated unit,
make sure that the power supply voltage is as indicated on the label (fig. C).
To guarantee the electrical safety of this equipment, it must be connected to
a grounded power socket in compliance with the current legislation of the
destination country.
For usage of the unit, as every electrical device, basic rules have to be followed:
- Do not touch or plug the equipment with damp or wet hands or feet;
- Do not pull the electrical cable to unplug it;
- Do not expose it to the atmospheric agents;
- Do not allow children to use it without adult supervision;
- Before starting any cleaning or maintenance operation, it is necessary
to unplug the equipment;
- In case of breakdown or bad functioning, disconnect the unit and do not attempt
to make any modification.
4) WORKING TEMPERATURE
This equipment is manufactured in conformity with the ambient conditions of
climatic class 3 (25°C – 60% R.H.) EN 441-4. The refrigerated unit maintains its
performance characteristics with an ambient temperature and relative humidity
of no more than: + 25° C and 60% R.H. (relative humidity). In case the ambient
conditions are not included in the above mentioned ones, a lower performance
must be expected.
5) INSTALLATION
The equipment must be installed in a suitable, dry, non-aired place and on a level
floor in order to avoid problems with alignment of the glass structure holes
during the assembling and to prevent noise during the working of the unit and
also to avoid higher energy consumption and a shorter compressor life (fig. G).
The refrigerated equipment should never be installed:
- near sources of heat such as radiators, direct or indirect sunlight or other
equipment which produce heat (fig. F);
- in line with draughts coming from doors, windows or air-conditioning systems
(fig. F).
Do not close or obstruct the ventilation openings of the refrigerating unit.
6) CLEANING
IMPORTANT – DURING THE WHOLE CLEANING OPERATION
USE WORKING GLOVES OF CLASS II TO PROTECT YOUR
HANDS ALL THE TIME
Before switching on the unit, take away the protective film that covers some
external and internal parts of the cabinet (for example the display surface).
Clean the equipment thoroughly, both inside and outside, using warm water and
a solution of bicarbonate of soda (1 tea spoon every 2 liters) or white vinegar.
Carefully dry the unit with a soft cloth. Never use detergent products, metal pads
or abrasive substances. Never use sharp objects; any damage resulting from the
use of these objects will not be covered by warranty. Never wash the cabinet
with water jets.
Once the cleaning is finished, switch the unit on through the
in fig. I and L and wait until the cabinet reaches the proper temperature for the
products that have to be displayed. It will take approx. 2 hours for the cabinet
to reach the proper temperature. The products to be displayed will have to be
already cold according to the cabinet temperature.
7) ELECTRICAL POWER / CONNECTION
First of all make sure that there is an efficient ground system in compliance with
the current legislation regarding electrical safety. When in doubt, request a careful
check from a qualified technician. The unit is equipped with the plug and electrical
cable mod. Schuco (fig. D).
GB
switch shown
A
C
D
F
B
E
G