Flint & Walling 3SDPH-L Instrucciones De Instalación

Notice to installing contractor: Instructions must remain with installation.
Product information presented
here reflects conditions at time
of publication. Consult factory
regarding discrepancies or
inconsistencies.
433047
412082
420816
433152
451558
451549
*Effluent systems should specify that pumps should not handle solids exceeding three fourths inch (3/4") in order to prevent large solids from entering leeching fields, mound systems
and etc. Where codes permit, sewage pumps can be used for effluent systems. Nonautomatic pump(s) with external level control recommended for septic tank effluent applications.
PRE INSTALLATION CHECKLIST - ALL INSTALLATIONS
1. Inspect your pump. Occasionally, products are damaged during shipment. If the unit is damaged, contact your dealer before using.
Do Not remove the test plugs in the cover nor the motor housing.
2. Carefully read the literature provided to familiarize yourself with specific details regarding installation and use. These materials should be retained for future reference.
SEE BELOW FOR LIST OF WARNINGS
1. To reduce the risk of electrical shock, a properly grounded receptacle or control box
must be installed in accordance with the governing codes. Never remove ground
pin from plug.
2. Make certain that the ground fault interrupter protected receptacle or control box is
within the reach of the pump's power supply cord. DO NOT USE AN EXTENSION
CORD. Extension cords that are too long or too light do not deliver sufficient voltage
to the pump motor, and they could present a safety hazard if the insulation were to
become damaged or the connection end were to fall into a damp or wet area.
3. Make sure the pump's electrical supply circuit is equipped with fuses or circuit breakers
of proper capacity. A separate branch circuit is recommended, sized according to the
National Electric Code for the current shown on the pump name plate.
4. Testing for ground. As a safety measure, each electrical outlet should be checked for
ground using a circuit analyzer which will indicate if the power, neutral and ground wires
are correctly connected to your outlet. If they are not, call a qualified licensed electrician.
5. FOR YOUR PROTECTION, ALWAYS DISCONNECT PUMP FROM ITS POWER
SOURCE BEFORE HANDLING. If pump is wired direct, de-energize the circuit at
the control box. Wear insulated protective shoes and do not stand in water. Pumps
equipped with a 3-prong ground plug are designed to help protect against electrical
shock. DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE GROUND PIN.
6. Installation and servicing of the pump, electrical circuits and hardware should only be
performed by a qualified licensed electrician.
7. Risk of electrical shock. Do not remove power supply cord and strain relief or connect
conduit directly to the pump. If the supply cable is damaged, it must be replaced by
the Manufacturer or an authorized Zoeller Service Station to avoid a hazard.
8. Pump contains oil which becomes pressurized and hot when operating. Allow 2½
hours after disconnecting before attempting service.
9. Pump is not intended for potable water due to possible contamination by oil contained
in the pump.
10. Risk of electric shock. These pumps have not been investigated for use in swimming
pools and marine areas.
11. Prop65 Warning for California residents: Cancer and Reproductive Harm- www.
P65warnings.ca.gov.
INSTALLATION INSTRUCTIONS
SUBMERSIBLE SUMP PUMPS
DEWATERING AND SEWAGE
MODELS
3SDPH-L 3SD-L
3SPH-L 3SP-L
3SEH-L 3SE-L
5SPH-L 5SP-L
5SDPH-L 5SDP-L
4EP 4EPF
BN4EP
40EC 40ECF
S1137 F1137
S1098 F1098
S1057
200ECF
ECP SERIES
95 N. Oak St. • Kendallville, IN 46755 • 1-800-345-9422
© All rights reserved.
Dewatering Effluent
X
X
X X
X
X
X X
X X
X X
X X
X X
X X
X
X
CAUTION
SEE BELOW FOR LIST OF CAUTIONS
1. Check to be sure your power source is capable of handling the voltage requirements
of the motor, as indicated on the pump name plate.
2. The installation of variable level float switches is the responsibility of the installing
party, and care should be taken that the tethered float switch will not hang up on
the pump apparatus or pit peculiarities and is secured so that the pump will shut
off. It is recommended to use rigid pipe and fittings and the pit be 18" or larger in
diameter.
3. Vent hole. It is necessary that all submersible sump, effluent, and sewage pumps
capable of handling various sizes of solid waste be of the bottom intake design to
reduce clogging and seal failures. If a check valve is incorporated in the installation,
a 3/16" vent hole must be drilled in the discharge pipe below the check valve and pit
cover to purge the unit of trapped air. Vent hole should be checked periodically for
clogging. The vent hole on a High Head application may cause too much turbulence.
If you choose not to drill a vent hole, be sure the pump case and impeller is covered
with liquid before connecting the pipe to the check valve. NOTE: THE HOLE MUST
BE BELOW THE BASIN COVER AND CLEANED PERIODICALLY. Water stream
will be visible when pump is operating.
4. Pump should be checked frequently for debris and/or build up which may interfere
with the float "on" or "off" position. Repair and service should be performed by an
Authorized Zoeller Service Station only.
5. Maximum operating temperature for standard model pumps must not exceed
130 °F (54 °C).
6. Do not operate a pump in an application where the Total Dynamic Head is less than
the minimum Total Dynamic Head listed on the Pump Performance Curves.
7. For health reasons, do not unplug, turn off, or disable pump and use pump tank
system as a way to fill up a sink or laundry tray, etc.
8. Pumps must be installed in accordance with the National Electrical Code and all
applicable local codes and ordinances. Pumps are not to be installed in locations
classified as hazardous in accordance with National Electric Code, ANSI, NFPA 70.
NOTE: Pumps with the "UL" mark and pumps with the "US" mark are tested to UL
standard UL778. CSA certified pumps are certified to CSA standard C22.2 No. 108.
FW0013
0119
Supersedes
0214
DATE
INSTALLED:
MODEL
NUMBER:
Sewage
X
X
X
X