Martin Yale 698 Instrucciones De Uso página 8

GB
OPERATING FUNCTIONS (Fig. 7):
1 = Main switch (emergency-stop)
This switch turns the machine either on
(position „1") or off (position „0").
Note: Each time the machine is switched on,
the multifunction relay is automatically
reinitialised. This is indicated by the control
displays (4 and 5) (fig. 7) which blink for a few
seconds.
2 = Rotary switch
a) „Cutting system forward" („1")
Turning this switch to position „1" starts the
cutting system and the conveyor belt.
Material can now be fed to the shredder.
b) „Cutting system reverse" („R")
Turning this switch to position „R" starts
the cutting system and the conveyor belt in
reverse.
c) „Cutting system stop" („0")
Turning this switch to position „0" switches
the shredder off, thereby halting the cutting
system and the conveyor belt.
3 = Pilot lamp „ready"
Lights when the main switch (1) is operated.
4 = Pilot lamp
„paper jam" / „motor fault" /
„Electrical malfunction"
a) Lights up when too much paper is fed to
the cutters (see description „AUTOMATIC
RESPONSE IN CASE OF OVER-
LOADING").
b) Blinks when the shredder motor is
overloaded, thereby activating the built-in
thermal protection. This leads to a break in
the circuit necessary for active operation.
For more information please turn to the
section headed „Motor Fault".
c) Blinks if one of the integrated contactors
fails. At the same time, the control display
(5) lights up. Please refer to the
„ELECTRICAL MALFUNCTION" heading
for further details.
5 = Pilot lamp
„collecting bag full" / „door open" /
„Electrical malfunction"
a) Blinks when the collecting bag is full and
needs to be emptied. At the same time the
machine switches off automatically.
b) Lights up when the door is not closed.
The machine then switches off automati-
cally and it cannot be started as long as the
door is open.
c) Lights up if one of the integrated contactors
fails. At the same time, the control display
(4) blinks. Please refer to the
„ELECTRICAL MALFUNCTION" heading
for further details.
OPERATION
OPERATING THE MACHINE:
The procedure is as follows:
1. Move the main switch (1) to position „1".
2. Turn the rotary switch „Cutting system forward"
(2) to position „1". The cutting system and the
conveyor belt now begin to run.
Attention: The machine will only operate when
a) the main switch (1) has been switched on
(position „1"),
b) the rotary switch (2) has been switched on
(position „1" or "R"),
c) the discharge door (10) for emptying the bag is
closed.
MATERIAL FEED:
The operator may not stand higher
than the machine itself stands, when
feeding paper to the machine!
Standing on an raised platform (such as
pallets or boxes placed in front of the
machine) reduces the distance between
operator and cutting system to a level
which does not meet the required safety
standard.
Feed material for the shredder can consist of
stacks of smooth paper (up to about 190 sheets,
depending on the type and size of paper); and
also crumpled paper and cardboard. Place any
material to be shredded on the moving conveyor
belt which feeds it to the cutting system.
It is advisable to place stacked paper diagonally
on the belt. In this way, the corner of the stack will
be fed to the cutting system first, thus avoiding a
sudden overload.
Never feed the shredder with a quantity
of paper exceeding the maximum
indicated in the technical data!
Should the machine become overloaded,
follow the instructions
„AUTOMATIC RESPONSE IN CASE OF
OVER-LOADING".
3 4 5
2 1
fig. 7
8
AUTOMATIC RESPONSE
IN CASE OF „OVERLOADING":
In case you accidentally overload the shredder, it
will automatically alleviate the problem as follows:
1. The cutting system becomes jammed. The pilot
lamp (4) (fig. 7) lights up.
2. The cutting system runs briefly in reverse,
thereby freeing the material to be shredded.
3. The cutting system automatically switches back
to forward mode.
This sequence is automatically repeated by the
machine up to three times. If the machine still
detects "overloading", the cutting system runs in
reverse once more for a specified period of time
and is then shut down.
Redistribute returned material and continue shred-
ding with a smaller amount of material. The ma-
chine must first be switched off with the rotary
switch (2) (fig. 7) (position "0"), and then back on
again (position "1") to this end.
EMPTYING THE COLLECTING BAG (Fig. 8):
When the collecting bag is full, the machine turns
off automatically. The pilot lamp (5) (fig. 7) lights
up. Empty the collecting bag as follows:
- Set a pallet or a trolley in front of the discharge
door in order to facilitate removal of the full bag.
- Open the door only a little bit (10) and level off
the cone of shredded material, which has
accumulated in the bag, with your hand.
- Open the door and swivel the bag frame with bag
out onto the pallet or trolley.
- Remove the rubber band, remove the bag and
dispose of its contents.
- Feed the empty bag through the bag frame from
below, and put the edges of the bag approxi-
mately 10 cm over the frame outwardly.
- Secure the bag to the frame with the help of the
rubber band.
under
- Close the door, at the same time swivelling the
bag frame and bag into the housing, and lock.
Note: The machine will only run with closed door!
14.95
9 11 10
fig. 8