Martin Yale 698 Instrucciones De Uso página 9

GB
TAKING OUT EXCESS PAPER
IN CASE OF OVERLOAD:
If the shredder has stopped due to an overload
(motor protection) take the excess paper out of
the inlet as follows:
1. Briefly turn the "cutting system reverse" switch
(2) (fig. 7) to position "R". The cutting system
and the conveyor belt run in reverse. The
material is released and returned by the con-
veyor belt.
2. Redistribute the returned material, or remove
some of it from the conveyor belt (12).
3. After allowing the motor to cool down for ap-
proximately 10 minutes (depending upon am-
bient temperature), the machine can once again
be started in the forward direction and shred-
ding can be continued (rotary switch (2) (fig. 7)
in position "1").
MOTOR FAULT:
The machine is equipped with a thermally protected
motor. Should this motor be overloaded, it will
switch off automatically. In such case the pilot
lamp „MOTOR FAULT" (4) (fig. 7) flashes.
After a cooling down period of approx. 10 minutes
(depending on the room temperature) you can
restart the machine and continue shredding.
CUTTING SYSTEM
MAINTENANCE (6x50 mm):
After approximately 2 hours of continuous op-
eration, spray some of the included special oil
onto an absorbant sheet of paper and feeded to
the cutting system.
Note: This involves no danger because all electri-
cal circuits are interrupted when the service flap is
opened, and the machine cannot be started.
GEAR BOX MAINTAINANCE:
Both synchron gears, as well as the chain wheels
and drive chains must be greased monthly.
The machine must be turned off at the
main switch (1) (fig. 7) and unplugged
before the machine is opened.
Description
Plastic bag, 600 x 490 x 1500 x 0,06 mm
Receptacle, 620 x 430 x 740 mm (optional)
Lubrication bottle, 125 ml (6x50 mm)
Angle guard set for extended table (optional)
Note: Please contact your dealer when ordering accessories and replacement parts.
MALFUNCTION
FAULT CHECKLIST:
If the machine is not functioning properly, you
should check the following:
- is the plug conneted to the mains?
- is the mains switch (1) turned on?
- is the rotary switch (2) turned on?
- is the door (10) closed?
- is the collecting bag full?
The bag has to be emptied.
- is there a paper jam?
Follow the instructions under „AUTOMATIC
RESPONSE IN CASE OF OVER-LOADING".
- is the motor overloaded?
Please refer to the section headed „MOTOR
FAULT".
- Has one of the contactors failed?
See description under „ELECTRICAL MAL-
FUNCTION".
- is there a phase failure?
Check the three-phase fuse at the power supply
socket, and replace if necessary.
If you still cannot isolate the fault or other
faults are statable, the machine shouldn't be
operated. Please report to / notify our customer
service department.
MAINTENANCE
Proceed as follows:
1. Remove the left-hand housing side panel and
the covering hood.
2. Grease the above mentioned parts with a brush
or a grease gun, and a standard, commercially
available grease.
3. Mount the side panel and the covering hood
and plug in the mains plug. The machine can
once again be placed into operation.
The machine may not be modified in
any way!
Operation of the machine is prohibited
if modifications are undertaken.
ENERGY SAVING TIP:
Be certain that the machine is turned off overnight
(main switch (1) (fig. 7) switched to „0").
ACCESSORIES
ELECTRICAL MALFUNCTION:
If the control display (5) (fig. 7) lights up and the
control display (4) (fig. 7) blinks at the same time,
one of the integrated contactors is no longer
functional and the machine may no longer be
operated.
Switch the machine off at the mains switch (1) (fig.
7), pull the mains plug from the socket and notify
your dealer.
Cutting width:
Cutting capacity:
6x50 mm:
5.8 mm:
11.8 mm:
Working width:
Power input:
Power output:
Supply voltage:
Pre-fusing:
(gl fuse, type 1 assignment)
Order-No.
400V-415V/50Hz:
99969
220V-230V/50Hz:
75970 200V/50Hz:
Length:
99943
Width:
86223
Height:
Noise level:
Weight:
9
Always unplug the machine from the
mains power supply, turn off the main
switch and lock it with a padlock before
opening the machine to carry out any
repairs.
TECHNICAL DATA
6x50 mm (cross-cut)
5.8 mm (strips)
11.8 mm (strips)
120-130 sheets (70 g/m
130-140 sheets (70 g/m
180-190 sheets (70 g/m
428 mm
7 kW
4 kW
400V/50Hz
230V/50Hz
415V/50Hz
220V/60Hz
200V/50Hz
200V/60Hz
25 A
32 A
35 A
1680 mm
1210 mm
1640 mm
approx. 63 dB(A)
approx. 435 kg
14.95
2 )
2
)
2
)