Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
iLOC
iLOC lets you control the transmitter remotely using your RD5100H
iLOC you can adjust the output frequency, power settings and use SideStep. iLOC
commands are sent over a Bluetooth module that can operate at distances of up to
450m (1400ft) in direct line of sight.
iLOC is a standard feature of RD5100H
O+ locators, and requires a Bluetooth equipped
2
transmitter (RD5100H
O+Tx).
2
NOTE: Operating in built up areas and in areas with high electromagnetic
interference may reduce iLOC's performance.
Pairing to a transmitter
To pair to a transmitter you require an RD5100H
Before you begin, you should switch off all nearby Bluetooth equipment as they may
interfere with the locator and transmitter's pairing process.
Preparing the locator:
1.
Press the
key to enter the menu.
2.
Scroll to the BT menu using the
or
3.
Press the
key to enter the BT menu.
4.
Scroll to the PAIR menu and press the
5.
Scroll to the BT-TX option.
NOTE: You must complete the pairing process within 90 seconds to prevent the
locator's Bluetooth connection from timing out.
Preparing the transmitter:
6.
Press the
key to enter the menu.
7.
Scroll to the BT menu using the
or
8.
Press the
key to enter the BT menu.
9.
Scroll to the PAIR option.
Starting the pairing process:
10. Press the
key on the transmitter followed by the
11. The transmitter and the locator will now attempt to pair.
When pairing is in progress, the transmitter and locator will display a flashing Bluetooth
icon. Pairing can take up to a minute. If the pairing process is successful, the transmitter
will display the
icon and the locator will display a persistent Bluetooth icon for the
duration of the connection.
O+ locator. With
2
O+Tx transmitter.
2
keys.
key to enter it.
keys.
key on the locator.
16
If pairing fails, ensure that any nearby Bluetooth devices are switched off or invisible
then repeat the process.
Once the locator and transmitter have successfully paired you can use iLOC to change
the transmitter's output frequency and power levels remotely from the locator.
Using iLOC
The locator and transmitter need to
be paired to use iLOC. For optimum
performance:
Try to minimize obstructions in line of
•
sight.
If possible, raise the transmitter off
•
the ground by 30-60cm (1-2ft).
Face the rear end of the transmitter
•
towards the locator.
Point the screen of the locator
•
towards the transmitter.
NOTE: If any iLOC commands fail, move closer to the transmitter and repeat the
process.
Changing frequencies
Once the transmitter and the locator are paired, you can change the transmitter's
output frequency remotely using the locator:
1.
On the locator, select the frequency you want by pressing the
frequency is displayed on screen.
2.
Press the
key to send the new frequency to the transmitter.
3.
The locator will display SEND momentarily and then OK if the transfer is
successful.
4.
If the transfer is unsuccessful, the locator will display a bluetooth error code error
code (see operation manual for details).
If the process fails, you may be out of range or there may be an error in the connection.
Move closer to the transmitter and retry the procedure. If the connection continues to
fail, return to the transmitter and reset the connection.
Adjusting power
iLOC lets you adjust the transmitter's power output remotely; you can also put the
transmitter into standby mode and then wake it remotely.
1.
Transmitter power options are located in the TXOUT menu on the locator.
Press and hold the
key to display the TXOUT menu.
key until the
17
Publicidad
Tabla de contenido
