Instrucciones De Mantenimiento; Mantenimiento De La Bañera - Baños 10 S.L Manual Del Instalador

9. INSTRUCCIONES DE MANTENIMIENTO

MANTENIMIENTO DE LA BAÑERA
Para prevenir la formación de sedimentos calcáreos, iniciar el llenado de
la bañera con agua fía o templada.
Después del vaciado de la bañera, enjuáguela y séquela, incluso las partes
metálicas, con una gamuza o esponja suave, inmediatamente después de
cada uso.
Limpiar siempre con agua jabonosa o un limpiador anticalcáreo (recomendado)
para evitar la perdida de brillo por depósito de cal. No utilizar productos
abrasivos o estropajos. No utilizar productos con base de acido clorhidrico
(salfumant).
Evite todo contacto con disolventes orgánicos, cigarrillos encendidos, lacas
o cualquier producto abrasivo.
Para la desinfección del sistema de hidromasaje y la bañera utilice el líquido
desinfectante de Baños 10. Verter el desinfectante (10 tapones por cada
100 l.) y tener 10 minutos la bañera en funcionamiento, luego vaciar la
bañera. Para bañeras con sistema de desinfección automático ver manual
de uso.
Para eliminar eventuales rayas en la superficie de la bañera, utilizar una lija
abrasiva al agua (nº1200), abrillantar con un pulimento exento de disolvente
(los utilizados para coches).
Para una eventual revisión o reparación del sistema de hidromasaje, debe
ser posible un facil acceso a la parte inferior de la bañera (zona del motor),
ya sea retirando uno de los faldones o através de la puerta de registro (min.
30 x 40 cm.).
Si detecta alguna avería, pongase en contacto con el Servicio de Asistencia
Técnica de Baños 10.
Tel.: 902 360 708 e-mail: sat@banos10.com
1. GENERAL RECOMMENDATIONS
GB
Installation should be performed by qualified personnel in accordance with
current local regulations.
The product should be checked before installation, since Baños 10 S.L. shall
take no responsibility for damages produced during its handling or transport.
Towards this end, all claims should be made to the transport agency, which
will have an insurance policy for this purpose.
Handle the bathtub with care, protecting it from possible bumps or scrapes.
Take the necessary precautions to protect the bathtub from dust, objects
falling on top of it and any other element that could damage its surface (acids,
sparks, cement, plaster, cigarettes, etc.).
The space designated for bathtub installation should be clean, with all leftover
building materials being removed. It is recommended that the floor be tiled.
In order to level the bathtub in its definitive position, turn the adjustable props
located at the ends of the metallic support.
It is vital that all of the bathtub's weight is supported by the adjustable props
and not by the edge of the bathtub itself.
Once the preceding operations have been performed, assemble the drain and
overflow, making sure to insert an elastic element between the trap and the
installation in order to compensate for possible movements. Check that the
entire assembly is watertight.
Check that the height-adjustable props are firmly seated.
It is recommended that the air inlet be installed on the part farthest away
from the wall.
In order to install bathtubs with hydromassage systems, it is absolutely
necessary that an electrical outlet be located nearby, which must comply
with current local electrical regulations and be compatible with the power
rating of the unit supplied.
For the installation of bathtubs with hydromassage that are equipped with
an automatic cleaning and disinfection system, an additional 1/2" cold water
inlet should be installed in the area allocated for this hook-up.
1.- OVERFLOW
2.- DRAIN PIPE (optional)
3.- METALLIC FRAME
4.- REGULABLE FEET
.