Publicidad
Idiomas disponibles
Idiomas disponibles
English
Before starting the assembly process, unpack all components of the staircase. Lay them out on a large surface and
check the quantity of all the pieces, by consulting the table TAB.1 (A = Code, B = Quantity).
Inside the staircase box you will also find a DVD which we suggest watching before proceeding to assemble.
For the USA only: call the customer support line at 1-888 STAIRKT, should you have any case of need.
Preliminary Assembly
1. Assemble the cylinders D32 into the treads (L02) by using the elements D33. Tighten by means of the article
C36. Insert the elements C13 and C31 into the cylinders D32 (fig. 2).
2. Assemble the parts BE3, CC5, CC6 onto the baluster (C07) (fig. A).
3. Carefully measure the floor-to-floor height and determine the required number of spacers (D03) (TAB.2).
4. Assemble the spacers ( D14, D03, D02) together in one piece. Do the same for the spacers (D04, D03, D02).
5. Assemble the base G03, B17 and B46 (fig. 1).
Assembly
6. Determine and mark on the floor the fixing point of the base (G03+B17+B46) by laying the laning (E03) on the
ceiling (fig. 3).
7. Place the base (G03+B17+B46) and drill with drill bit Ø 14 mm (fig. 3).
8. Fix the base (G03+B17+B46) onto the floor with the parts B13.
9. Screw the pole (G02) into the base (G03+B17+B46) (fig. 1).
10. Insert the base cover (D05) (fig. 4).
11. Insert the spacers (D14+D03+D02) (fig. 4).
12. Insert the first tread (L02) into the pole (G02). Then continue with the assembly, by adding alternatively one
spacer (D04+D03+D02) and one tread (L02). At this stage, the treads have to be positioned alternately one to
the right and one to the left, so as to distribute the weight in a balanced way (fig. 4).
13. When you reach the end of the pole (G02), screw the part B47 on it, then add the second pole (G02) and
continue with the stair assembly (fig. 4)
14. When you reach the end of the pole (G02), screw on it the part B46 and the part G01 (screw the part G01, till
its upper end sticks out approximately 15 cm (6'') from the stair height. Continue adding the treads, by using the
part D01 inserted into the spacers (D04+D03+D02) (fig. 5).
15. Finally add the stair landing (E03). Fasten the parts B05, B04 and screw the part B03 sufficiently, keeping in
mind that the treads still have to rotate (fig. 1).
Fitting of the Landing
16. Drill with drill bit Ø 14 mm in relation to the holes.
17. Block the part B13 completely (fig. 1).
Assembly of the Railing
18. Spread-out the treads (L02) fan-like, after having chosen the rotation direction (fig. 6). It is now possible to use
the stair.
19. Starting from the landing (E03), insert the first long railing baluster (C07): 1) measure the rise between the tread
(L02) and the landing (E03) and add 2,5 cm (1"), 2) cut the final part of the long baluster (C07), 3) pierce with
the drill bit 9 the landing (E03), 4) assemble the parts F01 using the parts B89, B07 and B23, 5) insert the just
cut baluster part between the lower part F01 and the tread (L02), 6) tighten the parts C31 of the tread and of
the landing, 7) insert and fasten with the part C31 the resting part of the baluster (C07) into the upper part F01
(fig. 1).Turn the balusters (C07) maintaining the holes looking to the stair centre.
20. Insert the longer balusters (C07), which connect the treads (L02), one by one. Tighten only the part C31 of the
lower tread (fig. 2).
21. Check the vertical position of all the assembled balusters (C07). This control is very important for best results.
22. Tighten securely the part B03 (fig. 6).
23. Tighten securely the part C31 of the upper tread (fig. 2).
24. Check once more the vertical position of the railing balusters (C07) and, if necessary, correct it, by repeating the
previous operations.
25. Fix into the floor in relation to the first baluster (C07), the part F01, by piercing with the drill bit 8. Use the parts
B11, B12, C29 and C31 (fig. 1).
26. Cut one long baluster (C07) to obtain the same size as all others you assembled previously (fig. 1). Set the first
baluster (C07) together with the reinforcing part (C30).
6 - cz
Publicidad
