Premier AB-3954AUGA Manual De Instrucciones página 8

Instructions of assembly method
1.Open the fan of the packaging to examine the integrity of parts, as above diagram;
2.First, put the two gaskets into the support tubes, and then insert into the corresponding holes
of the base, (such as the A section of installing the base components shown) use the screw
with a screw meson to tighten the support tubes. Finally the
Four casters should be installed to the alignment holes at the base, tightening with a
special wrench, and then put on the decorative base cover
3.Take out of the Fan Head (this part has been installed before leaving the factory), unscrewed
two tightening button to put it into the installed support tube.
4.Take out of the Guard Fastening Screw and tighten the Rear Guard on
Clockwise in Fan Head;
5.Take the blade and tighten it with the Blade Fastening Screw by Counterclockwise
on the motor shaft;
6.Finally tighten the Front Guard, first unscrewed the screw of Hoop Net a little, align and
hoop the Front Guard and Rear Guard then tighten the screw,
Fan components are assembled completely.
Using of Water Tank Diagram as follows:
Instructions of Cool Humidifier
(1)This Humidifier is mainly used on the bottom of fan, also used separately.
(Humidifier of C section can't be used alone)
(2) Installation and Instructions of Humidifier
1.Open the packaging to check if the product components、appearance、power
cable are damaged or lacked of. If there is missing object or breakage, please
put them into the packaging as usual and send them to our company.
(Cool Humidifier of B,C section have been installed)
2.Put the Fan Main fuselage steadily and put the Humidifier on the Fan bottom plate, it should
be not placed on the sunlight and too damp places.
3.Take the Humidifier Water Tank and turn over, follow the "Adding water"
arrow to open the cover on Counterclockwise, add clean water. (Pure water be advised)
4.Tighten the Water Tank Cover by Clockwise after filling with water, wipe the
water droplets surrounded by water tank and install the Water Tank well. (Diagram 1)
P-4
All manuals and user guides at all-guides.com
5.Insert Humidifier plug into the socket on the back of Fan main fuselage connect the Fan to the
AC 110V/60HZ Power Supply, turn on the Spray switch, Humidifier instruct light turn green,
2~5 seconds later ,mist will be sprayed
from the mist nozzle, Humidifier starts to work.
6. Mist volume can be adjusted and maximum mist volume is 380ml/h, it can be set by your
room's dry level. (Diagram)
7.When there is no water in the water tank, the safe device inside can turn off the
atomization circuit automatically, then no mist spray out, lacking water indicator light
illuminate (red), if continue to use, please cut off the power and fill with water in the
water tank again.
8.It is normal that there is a little mist overflowing around within several minutes'
humidifier working.
Control Operation of Remote-Control Fan
This Fan is utilized Electronic Touch Switch and Timer, replacing traditional switch and
timer. Besides keep the functions of traditional fan normal wind and timer, also increase
function of nature wind and
sleeping wind and remote control.
Operation Methods:
On the condition of connecting power supply, power indicator light illuminate, fan is under
standby mode. Now controlling the fan with the control buttons
on fan panel and using remote controller. (Put two batteries in the remote
controller before using)
1."OFF": press this button to cut off the power when the fan is working, working
indicator light quenches, fan stop working and controlling electric circuit recover to
status mode and remember the working mode before shutdown. Press this button
again, fan will work as
the memory mode (Timer and sleeping wind can't be remembered)
2."ON/SPEED": Open the fan and select fan speed:Low-Medium-High...... Cyclic selection.
3."WIND MODE": Choose mode of wind, such as Normal Nature Sleep ......
Cyclic selection.
1)Normal wind: Unit will work at Low-Medium-High speed.
2)Nature wind: Unit will operate under irregular status according to pre-set program,
Wind speed can be selected Low-Medium-High.
It is more comfortable and mild under nature mode.
3).Sleeping wind: Wind speed can be selected Low-Medium-High;
Motor is controlled by computer program so wind volume will decline slowly as body
temperature declining
P-5