Tabla de contenido
Publicidad
3. SELECT A DESIRED TRACK BY PRESSING SKIP UP
4. PRESS THE" MEM/CLK-ADJ " BUTTON (13) TO STORE THE TRACK INTO MEMORY.
5. REPEAT STEPS 3 AND 4 TO ENTER ADDITIONAL TRACKS INTO THE MEMORY IF NECESSARY.
6. WHEN ALL THE DESIRED TRACKS HAVE BEEN PROGRAMMED, PRESS " BAND/
PLAY THE DISC IN ASSIGNED ORDER.
7.
PRESS " STOP
" BUTTON (19) TO TERMINATE PROGRAM PLAY.
AFTER PROGRAM COMPLETE, PRESS "MEM/CLK-ADJ" BUTTON (13) REPEARTLY TO REVIEW THE
TRACKS BEING PROGRAMMED.
PRESS " STOP
FOR MP3 DISC / FILE, PRESS THE " FOLDER / PRE-UP " BUTTON (14) TO SELECT THE 1
NEXT FOLDER DIRECTLY AND HENCE TO SPEED UP THE SONG SELECTION.
THE PROGRAMMING MODEL WILL AUTOMATICALLY STOP IF NO BUTTON IS BEING PRESSED IN A
PERIOD OF ABOUT 10 SECONDS AFTER PRESSING THE " MEM/CLK-ADJ " BUTTON (13).
PLAYBACK OF MP3/WMA SONG VIA USB STORAGE MEDIA OR MEMORY CARD
CONNECTING
THE SYSTEM IS ABLE TO DECODE AND PLAYBACK ALL MP3 /WMA FILE WHICH STORED IN THE MEMORY
MEDIA WITH USB CONNECTING PORT OR SD/MMC MEMORY CARD.
1.
SET THE SYSTEM AT STANDBY MODE FIRST OR OTHER FUNCTION EXCEPT
SD OR USB MODE.
2.
PLUG-IN THE USB PEN-DRIVE WITH THE FACE UP & MAKE SURE IT GOING
INTO COMPLETELY OR INSERT THE MEMORY CARD IN THE DIRECTION OF
THE ARROW AS SHOWN IN THE LABEL ON THE UNDERSIDE OF THE
MEMORY CARD SLOT COVER. INSERT STRAIGHT WITHOUT BENDING.
CONNECTING THE USB UPSIDE DOWN OR BACKWARDS COULD DAMAGE
THE AUDIO SYSTEM OR THE STORAGE MEDIA (USB THUMB DRIVE /
SD/MMC CARD). CHECK TO BE SURE THE DIRECTION IS CORRECT
BEFORE CONNECTION.
3.
PRESS FUNCTIONS BUTTON (12) TO SELECT "
"
" USB MODE.
4.
THE SYSTEM WILL START READING THE STORAGE MEDIA AUTOMATICALLY AFTER CONNECTING, AND
LCD DISPLAY (2) WILL SHOW THE TOTAL NUMBER OF MP3/WMA FILES BEING DETECTED.
5.
REPEAT THE SAME PLAYBACK PROCEDURE AS PLAYING CD/MP3 DISC AS ABOVE.
REMARK
-
THE SYSTEM CAN DETECT AND READ THE FILE UNDER MP3 AND WMA FORMAT ONLY THOUGH THE
USB PORT.
-
IF CONNECT THE SYSTEM TO MP3 PLAYER VIA THE USB SOCKET, DUE TO VARIANCES IN MP3
ENCODING FORMAT, SOME MP3 PLAYER MAY NOT BE ABLE TO PLAY VIA THE USB SOCKET. THIS IS
NOT A MAUFUNCTION OF THE SYSTEM.
-
USB PORT DOES NOT SUPPORT CONNECTION WITH USB EXTENSION CABLE AND IS NOT DESIGNED
FOR COMMUNICATION WITH COMPUTER DIRECTLY
ENCODING OF CD/PHONO INTO MP3 FILE TO USB MEMORY
THE SYSTEM IS ABLE TO ENCODE NORMAL CD OR TURNTABLE TO MP3 FORMAT AND RECORDING AT
MEMORY MEDIA WITH USB CONNECTING PORT (OR SM/MMC CARD SLOT). BEFORE STARTING THE
ENCODING, PLEASE INSERT THE MEMORY MEDIA (USB PEN DRIVE OR SD/MMC CARD) TO THE SYSTEM &
MAKE SURE IT HAD ADEQUATE FREE MEMORY SIZE FOR RECRODING:-
A) CD ENCODING
I) ECNODING 1 TRACK / 1 DISC
1.
PERFORM NORMAL PLAYBACK OF THE CD TRACK YOU WANT TO ENCODE & RECORD,
2.
PRESS "
WILL START ENCODING.
3.
THE SYSTEM WILL SHOW "
4.
PRESS THE "
" OR RECORD ONE ENTIRE DISC " REC_ALL ".
5.
AFTER COMPLETING OF RECRODING, UNIT WILL STOP PLAYBACK AUTOMATICALLY.
II) ENCODING BY PROGRAM
1.
PLACE A CD WITH THE PRINTED SIDE FACING UP INSIDE THE TRAY & THEN CLOSE THE CO TRAY.
2.
SELECT THE DESIRE TRACKS BY FOLLOWING " CD DISC PROGRAMMING " PROCEDURES. THEN
PRESS " CD PLAY/PAUSE " BUTTON (17) TO START PLAYBACK.
" BUTTON (19) AT CD STOP MODE TO CANCEL ALL PROGRAMMED MEMORY.
" BUTTON (15) DURING THE PLAYBACK OF THE DESIRE TRACK AND THE SYSTEM
" & "
" BUTTON (15) REPEATLY AGAIN TO SELECT RECORD 1 TRACK " REC_ONE
OR DOWN
" SD CARD MODE OR
" AND FLASHING. ENCODING IS PERFORMING NOW.
E-5
BUTTONS (18/20).
" BUTTON (17) TO
ST
TRACK OF
Publicidad
Tabla de contenido
