Rear Connections - Numark CDN35 Manual De Inicio Rápido Del Usuario

8. Play/Pause: Starts the music from the cue point or
pauses it while in play. By pressing play after pause, a
new cue point will be set
9. Stutter: To start the music from the initial cue point.
10. Pitch Range: activates the pitch slider and adjusts the
amount of control the pitch slider has on the overall speed
of music. Tapping the pitch will toggle slider between 8%
and 16% pitch ranges. Holding the pitch for 3 seconds will
deactivate the pitch control.
11. Pitch Range LEDs: indicate current pitch range. When
both LEDs are off the pitch slider is not active
12. Pitch Slider: By moving the slider in the (+) direction the
speed of the music permanently speeds up. By moving the
slider in the (-) direction the speed of the music
permanently slows down. To match the speeds of two CDs
you can adjust the pitch. When the tempo of the music of
the CD you wish to match is slow compared to the tempo of
the other music, move the slider to the (+) side and match
the speed. When faster, move the pitch slider to the (-)
side. By making this adjustment the speeds will be
matched though the beats may not yet be aligned.
13. Search Button: Pressing this button allows you to use the
wheel and rapidly scan the music to find a cue point. The
search function automatically shuts off after 8 seconds of
non-use or you may toggle it off.
14. Jog Wheel:
Cue Function: As explained under "CUE", when the music is
paused and you rotate the wheel, music will sound. By
pressing play a new cue point is set.
Search Function: As explained under "SEARCH BUTTON",
when search is pressed and you rotate the wheel, the music
will rapidly scan the music to find a cue point.
1. Control Cable Connector- Plug in the 8-pin cable
included in here to connect the remote control and
main CD unit together
2. IEC Power Plug Connector - Plug your supplied
power cord in here.
3. Voltage Selector - Set this switch to the voltage for
your location.
4. RCA Audio Connectors - Connect your CD player to
your mixer from this line level output.
5. Digital Output - The format is type 2, form 1, also
known as S/PDIF (Sony/Phillips Digital Interface
Format). In order to use the digital output you should
not use variable pitch slider and the pitch bend
buttons. If you adjust the pitch, other devices may
not read the digital output properly because the
sampling rate changes
6. Remote Start Connector: Use this connector to plug
into your Fader Start-compatible mixer or remote
switch. This function is always active.
Fader - allows you to use an industry-standard fader-
a.
start mixer by attaching an 1/8" fader-start cable
between the unit and your mixer. Typically, if you
move the crossfader toward the active channel, the
attached CD player will play. When it is moved away
Pitch Bend Function: allows the user to temporarily change
the speed of the music to align beats. When the beats of
the music of the CD you wish to match is fast compared to
the tempo of the other music rotate the jog wheel counter
clockwise (to the left). When the CD is behind rotate the
jog wheel clockwise (to the right). The pitch changes
temporarily while the jog wheel is rotated. The faster you
rotate the wheel the more pitch is changed.
wheel results in a return to the original pitch.
15. LOOP IN: Used to set stutter and loop-in points.
16. LOOP OUT: Used to set loop-out points and release the
loop.
17. RELOOP/STUTTER: Used for repeated play (stutter) from
the loop-in point, repeating a previously set, and hot start.
18. BPM/PITCH Button: Switches the mode of the display
between showing the BPM and the percentage change in
pitch.
19. TAP Button: Tap this button with the beat of the music to
determine the current Beats Per Minute (BPM).
20. Relay: Used for setting alternating play start between
attached units
21. CD Drawer: Place your CDs you wish to play in here. This
unit is designed to play commercially available CD and
properly burned and finalized CDR formats. Due to
variances on the specification of certain CD burners and
CDs some discs home made CDs may not play properly.
22. Power Switch: Turn on and turn off the machine with this
button. The unit should always be shut down with this
button first before any external power is removed.

REAR CONNECTIONS

the unit will Cue or Pause, depending upon the CD
player setting. Some mixers allow the input channel
also to start the player.
Alternatively, a footswitch (found in most music
b.
shops) can be attached to this jack for creative mixing
techniques. Connector plugs are often ¼", so an
adapter to 1/8" will be needed. There are also two
types of footswitches that will work with this
connector. The first type is an on/off pushbutton
switch, and is generally used for switching channels on
guitar amps. The second is a momentary switch, and
is usually used for keyboard sustain pedals.
7. Remote Assignment Switch: This switch determines
the function of the Remote Start Connector. The
choices are below:
•
•
•
ON-OFF – for use with an ON-OFF switch.
MOMENTARY – for use with a momentary-
style switch.
MIXER – for use with a Fader Start-compatible
DJ mixer
Releasing the