Preventative Maintenance - Napa 791-2006 Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

aSSEmBLY inStrUCtionS
1. Attach legs (#12) to guide holder (#7) using (3) M8 hex bolts (#8), (3) spring washers (#9) and (3) flat washers (#10).
note: Do not tighten securely until the small and large braces have been attached.
2. Attach small braces (#14) to legs (#12) using (6) M8 hex bolts (#13), (6) spring washers (#9) and (6) flat washers (#10).
note: Do not tighten securely until large braces have been at tached.
3. Attach large braces (#15) to legs (#12) using (6) M8 hex bolts (#13), (6) spring washers (#9) and (6) flat washers (#10).
note: Now securely tighten all bolts.
4. Place bearing assembly (#5) on guide holder (#7) and screw handle (#3) on worm shaft (#6). Then, place handle grips (#4) onto ends of
handle (#3).
5. Insert the 6mm roll pin (#11) into the hole located near the bottom of the worm shaft (#6).
6. Set saddle (#1) on top of worm shaft (#6) and screw M8 hex bolt (#2) through saddle to secure on worm shaft.
oPErating inStrUCtionS
This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential
personal injury hazards. Obey all instructions to avoid possible injury or death.
1. Make sure the vehicle is properly supported, stable and at the required work height before positioning the stand(s) under the
vehicle component to be supported.
2.
Consult the lift and vehicle manufacturer for the proper positioning of the under hoist stands.
3. Once the stand(s) has been positioned properly under the vehicle, hold the stand's saddle in place with one hand while
turning the spin handle in a clockwise direction with the other hand. Remove the one hand from the stand's saddle when it comes
close to making contact with the vehicle.
4. Continue turning the stand's spin handle in a clockwise direction until it applies light pressure against the component. This
pressure should not exceed what is required to support the vehicle. Excessive pressure might cause the vehicle or its
component to become unstable.
5.
Before removing the stand from the vehicle, make sure the vehicle is still properly positioned on the lift. Removal of the stand
can be accomplished by turning the spin handle in a counterclockwise direction until the stand's saddle is clear of the vehicle.

PrEVEntatiVE maintEnanCE

This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to potential
personal injury hazards. Obey all instructions to avoid possible injury or death.
1.
Always store the stand in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive
dust, or any other harmful elements. The stands must be cleaned
matter before using.
2.
Use a general purpose grease to lubricate the wormshaft and foot pedal linkage if so equipped.
3. Every stand owner is responsible for keeping the stand labels clean and readable. Use a mild soap solution to wash external
surfaces of the stand. Contact Balkamp for a replacement label if your stand's label is not readable.
4. Inspect the stand before each use. Do not use the stand if any component is cracked, broken or bent. Do not use the stand if it
has loose or missing hardware or components, or is modified in any way. Take corrective action before using the stand again.
Premature wearing or damage to components caused by loose or missing hardware is not eligible for warranty consideration.
LimitED WarrantY
Please contact your local NAPA Auto Parts Store for details on warranty.
791-2006
of water, snow, sand, grit, oil, grease or other foreign
2
Model # 791-2006
UNDERHOIST STAND
2 TON
12/01/15

Publicidad

Tabla de contenido
loading

Tabla de contenido