Special Features; Safety Notes; Operating Instructions - Multiplex RX-6-DR light M-LINK Manual De Instrucciones

! These operating instructions are an integral part
of the product, and contain important information
and safety notes. Please store them in a safe place,
where you can find them at any time, and pass
them on to the new owner if you sell the receiver.
1. S
PECIFICATION
Order No.
Reception system
Servo channel count
Servo signal frame
rate
Signal resolution
Current drain
Aerial feed length /
aerial length
Operating voltage
Operating
temperature range
Weight
Dimensions
2. S F
PECIAL EATURES
•
Small, all-purpose 6-channel / 7-channel receiver exploiting
MULTIPLEX 2.4 GHz M-LINK technology, ideal for use in
small models.
•
Dual receiver:
The receiver contains two complete receiving circuits which
operate in parallel (receiver diversity).
This provides excellent reception quality by minimising
directional effects.
•
In-line connector arrangement:
Ideal for use even in slender fuselages (e.g. F3B, F3J, ...).
•
HOLD / FAIL-SAFE function.
•
Integral SET button and LED:
For binding, FAIL-SAFE programming, RESET and
operating status information.
3. S N
AFETY OTES
! Please read the instructions before using the receiver.
! Use the receiver only for the intended applications
( 4.).
! Ensure the power supply is of adequate capacity (
! Observe the installation notes (
! Carry out regular range checks (
4. A
PPLICATION
The RX-6/7-DR light M-LINK is a radio control receiver inten-
ded exclusively for use in model sport applications. It is prohi-
bited to use it for other applications, such as man-carrying
vehicles or industrial installations.
Operating Instructions RX-6-DR light M-LINK /
RX-7-DR light M-LINK 2.4 GHz receiver
RX-6-DR light RX-7-DR light
M-LINK M-LINK
# 5 5809 # 5 5810
2.4 GHz FHSS M-LINK
Frequency Hopping Spread Spectrum
MULTIPLEX-LINK
6
Fast response: 14 ms
Standard: 21 ms
12-bit, 3872 steps
Approx. 10 mA (excl. servos)
Feed cable: approx. 10 cm (2 x)
Aerial: approx. 3 cm (2 x)
3.5 V ... 9.0 V
4 - 6 NiCd / NiMH cells (NiXX)
2S LiPo / LiIo
- 20 °C ... + 55 °C
10 g
Approx. 38.0 x 28.0 x 11.5 mm
9.).
10.).
The RX-6/7-DR light M-LINK was designed with minimum
possible size and weight as top priority, and for technical rea-
sons such a unit cannot offer the same reception characteristics
as a larger, technically more sophisticated and more expensive
receiver. In the interests of safety we recommend that you use a
larger receiver wherever space permits. However, under normal
conditions it is possible to obtain an excellent reception perfor-
mance with the RX-6/7-DR light M-LINK provided that all the
RC components are arranged carefully, and the two receiver
aerials are deployed correctly.
5. C
OMPATIBILITY
The RX-6/7-DR light M-LINK 2.4 GHz receiver can only be used
in conjunction with transmitters which use MULTIPLEX M-LINK
transmission technology. As of June 2009 these are:
7
•
ROYALpro 7, 9 and 16 M-LINK.
•
ROYALevo or pro 7, 9 and 12 with firmware version V3.xx
and the HFM4 M-LINK 2.4 GHz RF module.
•
PROFImc 3010, 3030 and 4000 with the HFM3 M-LINK
2.4 GHz RF module.
•
COCKPIT SX M-LINK.
•
MULTIPLEX transmitters with the HFMx M-LINK 2.4 GHz
RF module.
6. P
OWER
The RX-6/7-DR light M-LINK receiver works with a wide range
of voltages from 3.5 V ... 9.0 V, i.e. with receiver batteries con-
sisting of 4 to 6 NiXX cells or 2S LiPo / 2S LiIo batteries.
! Note: if you wish to use a five-cell (six-cell) NiXX battery,
check that all the servos, gyros and other components to be
connected to the system are approved by the manufacturer for
use on operating voltages up to 7.5 V (9.0 V). If you wish to use
a 2S LiPo (2S LiIo) pack, check that all the servos, gyros and
other components to be connected to the system are approved
by the manufacturer for use on up to 8.4 V (8.2 V).
! Note: ensure that the power supply is adequate
A power supply system in good condition and of adequate
capacity for the specific application plays an indispensable role
in the safe operation of any model:
•
Use only high-quality receiver batteries of adequate capacity.
Balance and maintain them carefully, and charge them fully.
•
Ensure that all cables are of adequate conductor cross-
section. Keep all wiring as short as possible, and use the
absolute minimum of plug / socket connections.
•
Use high-quality switch harnesses exclusively.
•
Brief collapses in the power supply voltage (lasting a few
milli-seconds) have no adverse effect on the receiver. Longer
voltage collapses to below 3.5 V may cause a receiver reset,
resulting in a brief interruption in reception. This may be due
to a receiver battery which is almost flat, too weak or defec-
tive, cables of inadequate cross-section, poor-quality con-
nectors or an overloaded or defective BEC system.
6.).
Page 7
S
UPPLY