Publicidad
Idiomas disponibles
Idiomas disponibles
Operating Instructions •
Air Supply...
Tools of this class operate on a wide range of air pressures.
It is recommended that air pressure of these tools measures
90 PSI at the tool while running free. Higher pressure (over
90 psig; 6.2 bar) raises performance beyond the rated
capacity of the tool, which will shorten tool life because of
faster wear and could cause injury.
Always use clean, dry air. Dust, corrosive fumes and/or
water in the air line will cause damage to the tool. Drain the
air tank daily. Clean the air inlet filter screen on at least a
weekly schedule. The recommended hookup procedure can
be viewed in the above figure.
The air inlet used for connecting air supply, has standard
1/4" NPT . Line pressure should be increased to compensate
for unusually long air hoses (over 25 feet). Minimum hose
diameter should be 3/8" I.D. and fittings should have the
same inside dimensions and be tightly secured.
Lubrication...
Lubricate the air motor daily with quality air tool oil. If no
air line oiler is used, run a teaspoon of oil through the tool.
The oil can be squirted into the tool air inlet or into the hose
at the nearest connection to the air supply, then run the tool.
The amount of oil to be used is 1 ounce. Overfilling will
cause a reduction in the power of the tool.
Operation...
This ratchet wrench is rated at 3/8" USS bolt size. Rating
must be down graded for spring bolts, tie bolts, long cap
screws, double depth nuts, badly rusted conditions and
spring fasteners, as they absorb much of the impact power.
When possible, clamp or wedge the bolt to prevent spring-
back.
NOTE: Actual torque on a fastener is directly related to joint
hardness, tool speed, condition of socket, and the time the
tool is allowed to impact.
Use the simplest possible tool-to-socket hook up. Every
connection absorbs energy and reduces power.
NOTE: Soak rusted nuts in penetrating oil and break rust
seal before removing with ratchet wrench. If nut does not
start to move in three to five seconds, use a larger size
ratchet wrench. Do not use ratchet wrench beyond rated
capacity, as this will drastically reduce tool life.
SX116
SX116opman_101904.indd 4
Warning Information • Parts Breakdown
Air Inlet
Limited Warranty...
SUNEX INTERNATIONAL, INC. WARRANTS TO
ITS CUSTOMERS THAT THE COMPANY'S SUNEX
TOOLS ® BRANDED PRODUCTS ARE FREE FROM
DEFECTS IN WORKMANSHIP AND MATERIALS.
Sunex International, Inc. will repair or replace its Sunex
Tools ® branded products which fail to give satisfactory
service due to defective workmanship or materials, based
upon the terms and conditions of the following described
warranty plans attributed to that specific product. This
product carries a ONE-YEAR warranty. During this warranty
period, Sunex Tools will repair or replace at our option
any part or unit which proves to be defective in material or
workmanship.
Other important warranty information...
This warranty does not cover damage to equipment or tools
arising from alteration, abuse, misuse, damage and does not
cover any repairs or replacement made by anyone other than
Sunex Tools or its authorized warranty service centers.The
foregoing obligation is Sunex Tools' sole liability under this or
any implied warranty and under no circumstances shall we
be liable for any incidental or consequential damages.
Note: Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation
or exclusion may not apply to you. Return equipment or parts
to Sunex Tools, or an authorized warranty service center,
transportation prepaid. Be certain to include your name and
address, evidence of the purchase date, and description of
the suspected defect.
If you have any questions about warranty service, please
write to Sunex Tools. This warranty gives you specific legal
rights and you may also have other rights which vary from
state to state. Repair kits and replacement parts are available
for many of Sunex Tools products regardless of whether or
not the product is still covered by a warranty plan.
Shipping Address: Sunex Tools • 315 Hawkins Rd.
Travelers Rest, SC 29690
Mailing Address: Sunex Tools • P.O. Box 4215
Greenville, SC 29608
4
Rev. 10/19/04
10/22/04 1:35:01 PM
Publicidad
