Lp Gas Cylinder (Tank) Specifications And Installation - Signateur 1500111 Instrucciones De Montaje Y Cuidado

LP GAS CYLINDER (TANK) SPECIFICATIONS AND INSTALLATION:

• ONLY connect this grill to a Type 1 cylinder valve. The Type 1 valve can be identified with the large external threads on the
valve outlet.
• DO NOT connect to a propane cylinder exceeding a 9.1 kg/20 lbs capacity.
• DO NOT connect to a cylinder that uses any other type of valve connection device.
• Inspect the propane tank valve rubber seal for cracks, wear or deterioration prior to use. A damaged rubber seal can cause
a gas leak, possibly resulting in an explosion, fire or severe bodily harm.
• Turn off the cylinder valve when your grill is not in use.
• Handle the tank with care.
• Always secure the cylinder in an upright position.
• Never connect an unregulated LP gas cylinder to your grill.
• DO NOT expose LP gas cylinders to excessive heat or ignition sources.
• Allow only qualified LP gas dealers to fill or repair your LP gas cylinder.
• DO NOT allow the cylinder to be filled beyond 80% capacity.
• Read and follow all warnings and instructions that are on the cylinder and that accompany this product.
• DO NOT store a spare LP gas cylinder (full or empty) under or near your grill. This could cause excess pressure to be
expelled through the vapor relief valve resulting in fire, explosion, or severe personal injury, including death.
• Propane gas is heavier than air and will collect in low areas. Proper ventilation is extremely important. Keep the ventilation
opening(s) of the LP gas cylinder enclosure free and clear from obstructions and debris.
• DO NOT insert any foreign objects into the cylinder valve outlet as this could damage the rubber seal. Do not use propane
tank with a damaged rubber seal. A damaged rubber seal can cause a gas leak, possibly resulting in explosion, fire, severe
bodily harm, or death. Inspect rubber seal for cracks, wear or deterioration prior to use.
• Always keep cylinder (tank) in upright position during use, transit or storage.
LP GAS CYLINDER (TANK) SPECIFICATIONS:
LP gas cylinder (not supplied with this grill)
The LP (Liquid Propane) gas cylinder specifically designed to be used with this grill must be 30.5 cm/12 in diameter x
45.72 cm/18 in tall and have a 9.1 kg/20 lbs capacity incorporating a Type 1 cylinder valve and an over-filling protection device
(OPD).
This grill is designed to fit any 9.1 kg/20 lb cylinder available on the market. The pull out tray is adjustable for smaller bottom ring
cylinders.
The installation of this appliance must be in accordance with:
All applicable local codes, or in the absence of local codes, either:
• National Fuel Gas Code ANSI Z223.1 NFPA 54
• National Gas and Propane Installation Code: CAN/CGA B149.1
• National Gas Installation Code: CAN/CGA B149.1 (Canada)
• Propane Installation Code: CAN/CGA B149.2 (Canada)
To check your local codes, see your local LP gas dealer or natural gas company.
When purchasing or exchanging a cylinder for your gas grill, it must be constructed and marked in accordance with the
specifications for LP gas cylinders of the U.S. Department of Transportation (DOT) or the National Standard of Canada, CAN/
CSA-B339 Cylinders, Spheres and Tubes for Transportation of Dangerous Goods; and Commission, as applicable; and provided
with a listed over-filling prevention device (OPD), and provided with a cylinder connection device compatible with the connection
for outdoor cooking appliances.
The cylinder must also be equipped with:
• A shut-off valve terminating in a Type 1 gas cylinder valve outlet.
• A Type 1 valve that prevents gas flow until a positive seal is obtained.
• An arrangement for vapor withdrawal.
• A collar to protect the cylinder shut-off valve.
• A safety relief device having direct communication with the vapor space of the cylinder.
• A listed over-filling prevention device (OPD)
WARNING
DANGER
4