Publicidad
Idiomas disponibles
Idiomas disponibles
Assembling 040 floor baluster (go to point 24 if not present)
22. D etermine the position of the posts on the floor, on average one every 28 cm. Drill with a 10 mm bit and
insert items 046010, fixing them with chemical resin (not supplied). Fit the 033063 items with parts
009002 and 005001. Insert the 121019 balusters (H=910 mm) into items 033063, with the reinforcement
baluster 126009 about every metre, and lock them with the 001004 items. Fix the balusters to the wall
using element 033010 with articles 008004, 011053 and 033056 (drill with an 8 mm bit). Fit the 140053
handrail with the 002031 elements. Fit any connecting items 033103, 033105, 033107, and end items
033103 (Fig. 14).
23. I nsert the steel cables 004041 into the parts 034035 on the balusters, positioning the parts 004048 in
correspondence to the balusters at the end of the railing side. Secure the cables on one of the two ends
using the parts 004048 and 001011. Cut and secure the cables on the opposite end using the parts
004048, 001011 and 011040 (cover the cable ends with some adhesive tape to prevent them from fraying
when you cut them). Tighten the cables by screwing in the part 011040 in sequence from top to bottom (Fig. 1)
(Fig. 8).
Assembly of 030 railing
24. F inally, fit the 116006 support base, complete with tread, inserting the 031078 spacers, as calculated
earlier, and without definitively tightening component 003039 or drilling holes in the floor (Fig. 2).
25. F it components 005036, C63, 011064 onto the staircase balusters 122011 (Fig. 2) (Fig. 13)
26. I f necessary, cut the lower part of the 122011 balusters to obtain a railing height of about 100 cm. Insert
the 122011 balusters to connect the treads, starting from the top, on the side where the railing is needed.
Position the balusters using article C63, with the holed part facing upwards. Tighten components 001010,
taking care that they are vertical (Fig. 2).
27. C ut a piece of baluster 122011 to the necessary length to obtain spacers to connect treads. Insert lateral
connection spacers and secure them at the top with components 001010 and on the lower side with part
001004 in part BE5 (Fig. 2).
28. C heck that the entire staircase is vertical and trace on the floor the centre of the holes in the plate of base
support 116006. Remove the first and second treads and drill the floor with a 14 mm bit; insert parts
008021 and definitively tighten them. Replace the treads removed earlier (Fig. 2). If necessary, cut the 1st
post, insert the reinforcing part 046050 and fix it to the floor with items 002040, BF1, and 008004.
29. F ix the staircase to the wall using components 033010 and items 008004, 011053 and 033046 (drill with
an 8 mm bit) (Fig. 10).
30. C ut sections of handrail 140053 to length; assemble with part 046011, placing part 031076 between them.
For optimal fixing, the handrail must follow about 1/8 of a turn from the contact point.
31. F ix the handrail to the balusters with parts 002031; keep the balusters vertical. Insert angle parts 031061,
031071 and 031072 with screws 012014 and 001017 for changes of direction. Apply 031061 end caps to
the ends of the handrail with parts 004034 and 011069 (Fig. 2) (Fig. 9).
32. D etermine the position of the intermediate balusters. Drill with a 4.5 mm bit; assemble parts BF1 with screw
002040.
33. C ut the intermediate balusters at a height that can be determined on the staircase itself. Insert the balusters
in parts BE5, tighten with components 001004 and fix them to the handrail with parts 002031; keep the
balusters vertical (Fig. 2) (Fig. 9).
Assembling 030 floor baluster (go to point 35 if not present)
34. D etermine the position of the posts on the floor, on average one every 12 cm. Drill with a 12 mm bit and
assemble items 033008 with parts 008007. Insert the 122014 balusters (H=910 mm) into items 033008,
adding the 126009 reinforcement baluster about every metre, and locking them with the 001004 elements.
Fix the balusters to the wall using element 033010 with articles 008004, 011053 and 033046 (drill with an
8 mm bit). Fit the 140053 handrail to the balusters using the 002031 elements. Fit any connecting items
031072, 031071 and end items 031061 (Fig. 13).
Assembly of wall fixings and accessories
35. I nsert the 031075 components in the treads and the BE7 / 031054 elements in the lower part of the
121019 / 122011 balusters so that they correspond with the corner treads and, in the upper part, with the
121019 / 122011 lateral spacers (Fig. 1) (Fig. 2) (Fig. 8) (Fig. 9).
36. F it the closing elements for the 031062 supports; for the base support, cut in height before fitting (Fig. 1) (Fig. 2).
37. F irmly secure the staircase at the following points:
a) Insert the telescopic post 047087-047085 in an intermediate position (6th-7th riser) on the floor with
030-040_GENIUS_MY_RA.indd 12
12 - Genius 030 - 040 RA
09/12/11 14.29
Publicidad
