Move Refrigerator And Freezer To Final Location - Whirlpool SKT60 Serie Instrucciones De Instalación

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Install Leveler Legs
1. Remove the four hex-head screws on each roller assembly.
Set the roller assemblies aside.
2. Place the refrigerator/freezer on its back on top of a piece of
cardboard or other protective material.
3. Insert two plastic leveler legs (M) into each cabinet.
4. Return refrigerator/freezer to an upright position.
5. Adjust the leveler legs (M) so that each appliance is level,
plumb and at the same height as the other appliance.
NOTE: Now, the freezer and refrigerator each have two front
leveler legs (M) that are adjustable. The back of each cabinet
rests on two fixed supports.
6. Place a leveling tool on top of the cabinet. Check the level first
side to side and then front to back.
To raise a corner - Turn the leveler leg clockwise.
To lower a corner - Turn the leveler leg counterclockwise.
7. Repeat Step 3 for the other appliance until both the freezer
and refrigerator are level, plumb and at the same height.
Move Refrigerator and Freezer to
Final Location
WARNING
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
When Moving Your Freezer or Refrigerator:
Your freezer and refrigerator are heavy. When moving the
appliance for cleaning or service, be sure to cover the floor
with cardboard or hardboard to avoid floor damage. Always
pull the appliance straight out when moving it. Do not wiggle
or "walk" the appliance when trying to move it, as floor
damage could occur.
Move the First Appliance
IMPORTANT: If the electrical outlets are not centered in the back
wall of the opening, move the appliance on the opposite side of
the outlets into the opening first.
1. Cover the floor with cardboard or hardboard to avoid floor
damage.
2. Attach a plastic foam rear spacer (I) to the rear center of both
appliances.
NOTE: The rear spacers (I) ensure that the 2 appliances are
positioned the correct distance from the wall to avoid cabinet
damage.
3. Slide the first appliance into the opening far enough to
connect the power cord to the electrical outlet.
IMPORTANT: Wait 24 hours before plugging in your refrigerator
or freezer to avoid compressor failure.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
4. Plug into a grounded 3 prong outlet.
Move the Second Appliance
IMPORTANT: If the electrical outlets are not centered in the back
wall of the opening, move the appliance on the opposite side of
the outlets into the opening first.
1. Slide the second appliance into the opening far enough to
connect the power cord to the electrical outlet.
IMPORTANT: Wait 24 hours before plugging in your refrigerator
or freezer to avoid compressor failure.
2. Plug into a grounded 3 prong outlet.
3. If needed, either door may be adjusted horizontally by
loosening the three hinge bolts, moving the hinge and
retightening the bolts.
NOTE: Provide additional support for the refrigerator door
while the hinges are being moved. Do not depend on the door
gasket magnets to hold the door in place while you are
working.
Install the Top Plate
1. Insert one painted pan-head Torx
plate (D) and thread it into the cabinet. Use the two rear holes
in each cabinet.
NOTE: Do not completely tighten the screw.
†®TORX is a registered trademark of Saturn Fasteners, Inc.
®†
screw (L) through the top
7

Publicidad

Tabla de contenido
loading

Tabla de contenido