Programming The Dgp; Connecting The Data Gathering Panel To A Control Panel; Zone And Output Numbering; Technical Specifications - UTC Fire & Security interlogix ATS1210(L)E Manual De Instalación

LEDs
RX: LED flashes to indicate polling data is being received on
the system databus from the ATS control panel. If the LED
does not flash the control panel is not operational or the
databus is faulty (usually cabling).
TX: LED flashes to indicate the DGP is replying to polling from
the ATS control panel. If the RX LED flashes but the TX LED
does not, it indicates that the DGP is not programmed to be
polled in the control panel or that it is addressed incorrectly.
Connecting the data gathering panel to
a control panel
Refer to Advisor Master Installation Guide or Advisor
Advanced ATSx500A Installation and Programming Manual for
instructions.

Zone and output numbering

Zone numbering
ATS1210(L)E / ATS1211E has 8 zones that can be expanded
using ATS1202 (8 zones) to a maximum of 16 zones.
Output numbering
A DGP can have a maximum of 16 outputs available as relays
or open collector outputs. The output numbers are the same as
the 16 zone numbers allocated to the DGP address.
Advisor Master zone and output numbering
Control panel 1–16
DGP1 17–32
DGP2 33–48
DGP3 49–64
DGP4 65–80
DGP5 81–96
DGP6 97–112
DGP7 113–128
Advisor Advanced ATSx500A zone and output numbering
Control panel 1–16
DGP1 17–48
DGP2 49–80
DGP3 81–112
DGP4 113–144
DGP5 145–176
DGP6 177–208
DGP7 209–240
[1] Inputs 17 to 32 of DGP 15 cannot be used.
See Advisor Advanced ATSx500A Installation and
Programming Manual for more information.
P/N 1077869 (ML) • REV C • ISS 22MAY19
DGP8 129–144
DGP9 145–160
DGP10 161–176
DGP11 177–192
DGP12 193–208
DGP13 209–224
DGP14 225–240
DGP15 241–256
DGP8 241–272
DGP9 273–304
DGP10 305–336
DGP11 337–368
DGP12 369–400
DGP13 401–432
DGP14 433–464
DGP15 465–480 [1] /
465–496

Programming the DGP

DGP menu
ATS1210(L)E / ATS1211E provides a menu through which a
number of options can be set. In addition the status of
ATS1210(L)E / ATS1211E itself or inputs can be viewed. See
Figure 5.
Extended mode
To enable anti-mask detection it is necessary to select
Extended mode. Standard mode is needed for backwards
compatibility. Default is Extended mode.
Configuring Advisor Master control panel
Activate polling ATS1210(L)E / ATS1211E.
1. Enter menu 4 of the control panel installer menu, and add
the address for the device, then press Enter.
Press Enter, select the "DGP address" and press Enter
2.
again to enter the DGP details.
3. Select the device type 5 (advanced DGP).
4. Press Enter until you are back to the main menu.
To enter the programming menu for ATS1210(L)E / ATS1211E
from Advisor Master control panel:
1. Enter menu 28 of the control panel installer menu.
2. Press 1 Enter followed by the DGP address selected and
Enter to enter the DGP menu. The display now shows
"ATS121x" followed by the version number.
3. Press Enter to proceed to the menu or press the menu
number followed by Enter to go to a menu item directly.
For more information on control panel programming, see
Advisor Master Programming Manual.
Configuring Advisor Advanced ATSx500A control panel
1. Enter Device menu > Edit Rkp&Exp > Exp devices > Add
new.
2. Enter the expander address (set by DIP switch) and press
Enter.
To enter the programming menu for ATS1210(L)E / ATS1211E
from Advisor Advanced ATSx500A control panel:
1. Enter Expander devices menu.
2. Select the appropriate expander by entering its number, or
moving the cursor with arrow keys.
3. Go to the Expander menu.
For more information on control panel programming, see
Advisor Advanced ATSx500A Installation and Programming
Manual.

Technical specifications

Supply voltage
Current consumption
Data retention
Dimensions (H x W) (size BB board)
10.5 to 13.8 V (12 V nom.)
53 mA max.
> 40 years
90 x 80 mm
3 / 24