Battery Recycling - RotoZip SCSØ2 Spiral Saw Manual Del Usuario

IMPORTANT SAFETY INSTRUCTIONS
BATTERY CHARGER AND BATTERY PACK
SAFETY INSTRUCTIONS
1. SAVE THESE INSTRUCTIONS - This
manual contains important safety and operating
instructions for battery charger Model 100138.
2. Before using battery charger, read all
instructions and cautionary markings on
battery charger, battery, and product using
battery.
3. To reduce risk of injury,
CAUTION
!
charge only Roto Zip Tool
Corporation 12 volt rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
4. Avoid dangerous environments. Do not
use charger in rain, snow, damp or wet
locations. Do not use battery pack or charger in
the presence of explosive atmospheres
(gaseous fumes, dust or flammable materials)
because sparks may be generated when
inserting or removing battery pack, possibly
causing a fire.
WARNING
!
5. Charge only Roto Zip
Tool Corporation 12 Volt battery pack
100109 in this charger. Use of an attachment
not recommended or sold by the battery charger
manufacturer is hazardous and may result in a
risk of fire, electrical shock, or injury to persons.
6. This charger is equipped with a polarized
plug (one blade is wider than the other.)
This plug will fit in a polarized outlet only
one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install a
polarized outlet. Do not change the plug in
any way.
7. Maintain charger cord. When unplugging
charger, pull plug rather than cord to reduce the
risk of damage to the electrical plug and cord.
Never carry charger by its cord. Make sure
cord will not be stepped on, tripped over or
subjected to damage or stress. Do not use
charger with damaged cord or plug. Have
damaged cord replaced immediately with
identical replacement parts.
8. Do not use an extension cord unless it is
absolutely necessary. Using the wrong,
damaged or improperly wired extension cord
could result in the risk of fire and electric shock.
If an extension cord must be used, plug the
charger into a properly wired 16 gauge or larger
extension cord that is in good electrical
condition. The pins on the plug of the extension
100 - 120 VOLT CHARGER
CORD LENGTH WIRE SIZE (AWG)
(MEASURED IN FEET)
25' 18
18
50'
100' 18
cord must be the same
220 - 240 VOLT CHARGER
WIRE SIZE
CORD LENGTH
(millimeters)
(MEASURED IN METERS)
50 0.75
75 1.00
number, size and shape as those of the plug on
the charger. The wire size must be large
enough for AC ampere rating of charger as
specified in the following table.
9. Do not use charger with damaged cord or
plug. Have a damaged cord replaced
immediately with identical replacement parts.
(a) Cord replacement for Roto Zip Tool
Corporation Charger No. 100138 must be done
at a Roto Zip Tool Corporation service facility
since special tools are required to replace it.
(b) Cord replacement for Roto Zip Tool
Corporation Charger No. 100138 must be done
with an identical cord.
10. Do not use charger or battery pack if it
has received a sharp blow, been dropped or
damaged in any way. Do not disassemble.
Incorrect assembly may result in the risk of
electric shock, fire or exposure to battery fluids.
If it is damaged, take it to a Roto Zip Tool
Corporation service facility.
11. To reduce the risk of electric shock,
always unplug charger before cleaning or
maintenance. Turning off controls will not
reduce this risk. Use a Ground Fault Circuit
Interrupter (GFCI) to reduce shock hazards.
12. The charger is not intended for young
children or infirm persons without
supervision. Young children should be
supervised so that they do not play with the
charger.
-4-
SPECIFICATION
MODEL NUMBER TYPE
100138 No type number
100138 2
WEIGHT - ALL MODELS 2.7 lb. (1.25Kg)

Battery Recycling

The RBRC Battery Recycling Seal
on the nickel-cadmium (Ni-Cd)
battery contained in our Spiral
Saw™ power tool indicates
Roto Zip Tool Corpoation is voluntarily
participating in an industry program to collect
and recycle batteries at the end of their useful
life, when taken out of service in the United
States or Canada. The RBRC program
provides a convenient alternative to placing
used Ni-Cd batteries into the trash or municipal
waste stream, which is illegal in some areas.
Please call 1-800-8BATTERY for information on
Ni-Cd battery recycling in your area. Roto Zip
Tool Corporation's involvement in this program
is part of our commitment to preserving our
environment and conserving our natural
resources.
INPUT VOLTAGE OUTPUT CURRENT
1.5 Amps
120V 50/60Hz
120V 50/60Hz 1.6 Amps
-5-