Setting At Work; Useful Information - DVA ISI Serie Manual De Istrucciones

instruction manual
water softener
10.3 QUICK CYCLE:
To check the correct functioning of the different regeneration
steps, follow the instructions below:
1) Press and hold down
in vertical fall; a manual regeneration cycle will begin.
2) Wait for a few seconds, then press
show the current step of the cycle, C1.
3) Press at the same time to pass to the following step
of the regeneration.
4) Wait for a few seconds, then press
step of the cycle on the display ("C2").
Repeating the previous commands, it is possible to go past
all the 7 steps until the "service" position, and then the
display will show back the set time.
If you press and hold down
seconds, the valve, whatever its position, will go past all
the steps non-stop, until the service step
10.4 SELECTING THE REGENERATION PROGRAM
The valve is provided with 4 different regeneration programs:
U1, U2, U3, U4.
Every program has different time values for each regeneration
step.
The model ISI 5 require the program "U3".
The models ISI 8 and ISI 12 require the program "U4".
To select the regeneration program, press and hold down
at the same time for 5 seconds, until the display
shows the program in use.
Press to select U4 (U3 for ISI 5) and wait for a few seconds
until the display shows back the set time.
Press and hold down
that "U4" appears on the display (U3 for ISI 5).

11) SETTING AT WORK

After the installation is complete, follow the procedure below:
1. Close the water inlet and outlet taps (fig. 3, B, D), then
plug in the fixture.
2. Press and hold down
conds; the valve will immediatelly position to the service
step and the display will show the time.
3. Press until the display shows two horizontal lines in
vertical fall.
4. Wait for a few seconds, then press
that "C1" appears on the display.
5. Unplug the fixture.
6. Slowly open the water inlet by half (fig. 3, D) and leave it
in this position for about 3 minutes.
When all the air is out, open the water inlet completely.
Let the water flow abundantly until it is crystal clear;
7. In the meantime, pour some water in the brine tank and
cover the suction pipe;
8. Plug in the fixture again.
9. Press at the same time to pass to step C2.
10. Press briefly and check that "C2" is written on the
display; wait until the water level in the vat decreases and
almost all the water is sucked in.
11. Press to pass to step C3.
12. Press and check that "C3" appears on the display.
When the cycle is complete (it will take about 10 minu-
tes), check that the vat still contains some water.
13. Check that the inlet and outlet taps are completely open
(fig. 3, B, D).
14. Add salt, up to more than half of the vat (fig. 7).
15. Press briefly, and the display will show a flashing dot.
It's now possible to program a regeneration at a fixed
time.
10
ISI Series
until the display shows two lines
. The display will
to see the current
at the same time for 5
again for 5 seconds and check
at the same time for 5 se-
briefly and check
12) ADJUSTING THE MIXER SCREW
The water softener supplies water free of hardness. In some
cases, however, a hardness residual in the water can be im-
portant.
The mixer allows a certain amount of water to pass directly
from the inlet to the outlet of the water softener, without being
softened by resins.
Screwing up the mixer screw (fig. 8, E) you can gradually
increase the hardness of the outcoming water.
Please remember that this operation must be carried out very
carefully.
At the end of the adjustment, we advise you to let some water
flow out and to measure its hardness.
13) MAINTENANCE
13.1 FOR THE USER
Maintenance for users only consists in refilling the brine pe-
riodically with sodium chloride (NaCl, common salt), in lack
of which the water softener will not be able to eliminate water
limy hardness.
ATTENTION! Never use substances different from
common salt (NaCl).
13.2 FOR INSTALLERS
For an ideal working, it is advisable to perform the following
operations periodically:
1) Clean the brine and remove any sediment from the suction
pipe (fig. 1) every six months;
2. Clean the injector (fig. 8, B) and its filter (fig. 8, A) at least
once a year, following the instructions reported below:
• Close the water inlet and outlet taps (fig. 3, B, D)
• Press and hold down
zontal lines in vertical fall.
• Wait for a few seconds, then press
the cycle step (C1).
• Unplug the fixture.
• Unscrew and remove the ejector (fig. 8, B), the filter (fig. 8,
A) and the brine control (fig. 8, C).
• Wash the components with water and make sure the hole
in the ejector isn't blocked.
• Carefully place the parts again in their seats.
• Slowly open the water inlet and outlet taps, and wait for a
few minutes.
• Plug the fixture.
• Press and hold down
conds. The valve will automatically position to service step.
• The display will then show back the time (fig. 6, B)

14) USEFUL INFORMATION

Experience teaches that often malfunctioning of water softe-
ners is caused by an incorrect outlet pipe installation (fig. 4,
A). For this reason, we advise you to perform a correct instal-
lation (fig. 3, F), using the outlet pipe provided.
Where possible, it is advisable to install a filter before the
water softener to get rid of substances that could compromise
the good functioning of the fixture.
ENGLISH
until the display shows two hori-
briefly to visualize
at the same time for 5 se-
Istruction Manual ISI SERIES