Interlogix ATS7320 Hoja De Instalación página 3

•
For up/downloading via the GSM module use a SIM card
that has fax and data enabled.
•
ATS7320 does not support data upload/download when
used with Advisor Master.
•
ATS7320 cannot be connected remotely using the
ATS7072 expander kit.
•
This device can be installed only by a qualified electrician
or other suitable trained and qualified person.
Caution: Ensure that there is only one GSM/GPRS dialler
(ATS7310, ATS7320, TDA7400, TDA7400NG, or ATS7500)
installed on the MI bus, to avoid any configuration conflicts.
Mounting location
ATS7320 must be mounted inside an ATS panel housing.
WARNINGS
•
Disconnect the mains power before opening the cabinet.
Disconnect the AC mains plug from the AC mains wall
socket, or disconnect the mains using the dedicated circuit
breaker.
•
Disconnect the battery (when applicable).
Mounting the unit
Figures 2 to 6
(1) Screws
(2) Flat cable
(3) Extension pillars with the plastic rings on existing pillars
(4) Screws on clips
(5) Screws on extension pillars
Mounting ATS7320 into ATS2000, ATS3000, ATS4500, and
ATS1000A-SM/ATS2000A-SM control panels
See Figures 3 and 5.
1. Remove the screws (item 1) and lift off the control panel
PCB.
2. Place the extension pillars with the plastic rings on top of
the existing pillars (item 3).
3. Place the clips in the square holes (item 4).
4. Mount ATS7320 using the screws and extension pillars
(item 5).
5. Place the ATS control panel PCB back into its original
position.
Mounting ATS7320 into ATS1000, ATS4000, and
ATSx000A-MM/ATSx500A-MM control panels
See Figures 2, 4, and 6.
1. Place the clips in the square holes (item 4). Use metal
pillars when available.
2. Mount ATS7320 using screws.
P/N 466-2906-ML • REV A • ISS 13JUL17
Connecting the GSM module
WARNING: Disconnect the AC mains plug from the AC mains
wall socket.
1. Connect the flat cable (item 2 in Figures 2 to 6) between
the control panel (MI connector) and ATS7320 (connector
CON2 or COM3).
2. Connect the antenna to the GSM module.
3. Insert the SIM module into the SIM socket (SIM).
4. Apply power to the control panel and to the GSM module.
5. Check the field strength (RSSI LED). When required,
move the antenna in order to get the best signal.
Operating instructions
Refer to the appropriate control panel installation manual (ATS
Advisor Master or ATS Advisor Advanced) for details on:
•
Operating instructions for all functionalities
•
Available keys, codes, and related details
•
User programmable functions
Testing the GSM module
To check the correct reporting to the Central Station, we
recommend you to create an event (for example, a test call, an
opening, or a closing event), and to ensure that the Central
Station receives this event successfully.
Description of the ATS7320
Figure 1
Item Description Function
(1), (2) CON2, CON3 MI bus, system connector. Connects to
the ATS panel.
(3) DIP switch See Table 1 below.
(4) LEDs Status LEDs.
(5) SIME LED SIM Status LED.
(6) CON4 Diagnostics / update.
(7) CON6 Diagnostics.
(8) ANTENNA SMA antenna connector.
(9) SIM SIM socket. Holds GSM SIM card.
DIP switch
The DIP switch provides the functionality described in Table 1
below.
Table 1: DIP switch description
No. Name Function
1. HL Modem update
2. TEST Factory test mode
3. BOOT Firmware update mode
4. Reserved
Default value
Off
Off
Off
Off
3 / 44