Cleaning And Care - Delta MultiChoice 14 T20 Serie El Manual Del Propietario

Ocultar thumbs Ver también para MultiChoice 14 T20 Serie:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

14 T20 Series Installation
5
Adjusting the Rotational Limit Stop
Rotational Limit Stop
IMPORTANT:
The Rotational Limit Stop is used to limit the
amount of hot water available such that, if set
properly, the user will not be scalded if the han-
dle accidentally is rotated all the way to "hot"
when a person is showering or filling a tub. The
first position allows the LEAST amount of hot
water to mix with the cold water in the system.
In the first position the water will be the coldest
possible when the handle is turned all the way
to hot. As you move the Rotational Limit Stop
clockwise, you progressively add more and
more hot water in the mix. The last position will
result in the greatest amount of hot water to
the mix, and the greatest risk of scald injury if
someone accidentally turns the valve handle
all the way to the hot side while showering or
filling a tub.
WARNING: In some instances, setting the
Rotational Limit Stop in the hottest position
(full clockwise) could result in scald injury.
It is necessary to adjust the Rotational
Limit Stop so that the water coming out
of the valve will not scald the user when
the handle of the valve is rotated to the
hot side.
• According to the majority of industry stan-
dards, the maximum allowable temperature of
the water exiting the valve is 120°F (Your local
plumbing codes may require a water tempera-
ture less than 120°F).
• The Rotational Limit Stop may need to be re-
adjusted seasonally if the inlet water tempera-
ture changes. For example, during the winter,
the cold water temperature is colder than it is
during the summer which could result in vary-
ing outlet temperatures. A water temperature
for a comfortable bath or shower is typically
between 90°F - 110°F.
• Use a thermometer to set the rotational limit
stop. Do not rely on the digital display tempera-
13 / 14 Series Installation
Disc
Stem
ture. There may be up to a 7° F difference in
temperature of the water coming out of the
spout or showerhead as compared to the
reading on the display.
• Run the water so that the cold water is as
cold as it will get and hot water is as hot as
it will get. Place the handle on the stem and
rotate the handle counterclockwise until the
handle stops.
• Place a thermometer in a plastic tumbler
and hold in the water stream. If the water
temperature is above 120°F, the Rotational
Limit Stop must be repositioned
counterclockwise to decrease valve outlet
water temperature to be less than 120°F
or to meet the requirements of your local
plumbing codes.
• To adjust the temperature of the water
coming out of the valve, remove the o-ring
and pull the disc back to a position where it is
possible to remove the Rotational Limit Stop
and readjust the teeth engagement position to
the desired temperature. Counterclockwise will
decrease the outlet temperature, clockwise will
increase the outlet temperature. Temperature
change per tooth (notch) could be 4° - 16°F
based on inlet water conditions. Repeat as
necessary. Push disc until fully seated and
replace o-ring.
WARNING: Failure to re-install disc and
o-ring after setting Rotational Limit Stop
could result in scald injury.
• MAKE SURE COLD WATER FLOWS
FROM THE VALVE FIRST. MAKE SURE
WATER FLOWING FROM THE VALVE
AT THE HOTTEST FLOW POSSIBLE
DOES NOT EXCEED 120°F OR THE
MAXIMUM ALLOWED BY YOUR LOCAL
PLUMBING CODE.
10
Faucet leaks from tub spout/showerhead:
SHUT OFF WATER SUPPLIES.
Replace seats and springs–Repair
Kit RP4993. Check condition of lower O-rings and
replace if necessary RP14414. See Helpful Hints
1, 2, & 3.
If leak persists:
SHUT OFF WATER SUPPLIES.
Replace valve cartridge RP46074.
See Helpful Hints 1, 2, 3 & 5.
Unable to maintain constant water temperature:
Replace valve cartridge RP46074 or follow
instructions in Helpful Hints 1, 2, 4 & 5.
Helpful Hints:
1. Before removing valve cartridge assembly for any
maintenance, be sure to note the position of the
rotational limit stop on the cap. The valve cartridge
assembly must always be put back in the same
position. BE SAFE! After you have finished the
installation, turn on valve to make sure COLD WATER
FLOWS FIRST.
2. To remove valve cartridge from body, shut off
water supplies and remove handle and bonnet
nut. Do not pry the valve cartridge out of the body
with a screwdriver. Place handle on stem and rotate
counterclockwise approximately 1/4 turn after the stop
has been contacted. Lift valve cartridge out of body.
3. To remove seats and springs, remove valve
cartridge. Separate cap assembly from the
housing assembly by rotating the cap assembly
counterclockwise 90
(degrees). Separate cap and
o
housing assemblies. Remove seats and springs and
replace. Place the largest diameter of the spring
into the seat pocket first and then press the tapered
end of the seal over the spring. Reassemble valve
cartridge and replace in body following instructions
given in 1 above.
4. If the water in your area has lime, rust, sand or
other contaminants in it, your pressure balance
valve will require periodic inspection. The frequency
of the inspection will depend on the amount of
contaminants in the water. To inspect valve cartridge
remove it and follow the steps in note 1 above.
Turn the valve to the full mix position and shake the
cartridge vigorously. If there is a rattling sound, the
unit is functional and can be reinstalled following
instructions given in note 1 above. If there is no rattle,
replace valve cartridge EP78407.
5. Push disc until fully seated. See page 10 for
more details.
To order replacement parts, visit
www.deltafaucet.com or call
1-800-345-DELTA (3358)
Care should be given to the cleaning of this prod-
uct. Although its finish is extremely durable, it can
be damaged by harsh abrasives or polish. To clean,
simply wipe gently with a damp cloth and blot dry
with a soft towel.
14 T20 Series Maintenance
To change batteries:
A.
1
Using an Allen wrench to loosen the set screw (1),
remove the handle from the stem. Note: If no set
screw hole - handle may have cap with screw.
B.
1
Remove the escutcheon (1) by rotating it
counterclockwise until it can be pulled from the
backplate. Carefully, slide the escutcheon over the
sleeve and remove.
C.
1
2
Remove battery cover (1) by pushing in the direc-
tion of the arrow. Remove old batteries and insert
3 new "AAA" batteries (2) making sure to orient in
proper direction. Reinstall parts in reverse order.

Cleaning and Care

Warning: Scrubbing Bubbles
®
Bathroom Cleaner
and Lysol
®
Basin Tub and Tile Cleaner must not be
used on the clear knob handles and levers. Use of
these cleaners can result in cracked or severely
damaged handles. If overspray gets onto the
handles, immediately wipe them dry with a soft
cotton cloth
11

Publicidad

Tabla de contenido
loading

Tabla de contenido