Maintenance And Cleaning; Technical Data; Ec Declaration Of Conformity - ATIKA FM 2 Manual Original

Selecting the measuring mode
1. Keep the key pressed for 3 seconds. The indicated
symbol will flash.
2. Change to the next measuring mode by pressing the key
within 3 seconds.
3. Once you have selected your desired measuring mode wait
for approx. 4 seconds until the symbol ceases flashing.
Then, the selected measuring mode is active.
Note: Firstly measure on dry material and then compare the
values with the material to be measured to get a sense for the
measured values. To be able to evaluate the moisture
distribution within the material measure on different points.
Building moisture measurement
1. Select the symbol.
2. Remove the protective cap
3. Exert slight pressure to press the puncture probes
material.
4. The display will show the measured value and a LED lights.
LOW (green) = 0.3 – <0.6%
MID (yellow) = 0.6 – <0.9%
HIGH (red) = >0.9 – 2.0%
5. Reattach the protective cap after completion of the
measurement.
Wood moisture measurement
1. Select the symbol.
2. Remove the protective cap
3. Stick both probes into the material (approx. 3 - 4 mm).
4. The display will show the measured value and a LED lights.
LOW (green) = 8 – <14%
wood is dry and suited as firewood,
no rotting
MID (yellow) = 14 – <20 %
marginal wood moisture,
further checks required
HIGH (red) = >20 – 60 %
wood moisture too high,
wood not suited as firewood,
risk of rotting
Note: Please refer to the "Wood Correction Table" (see
page 29/32).
5. Reattach the protective cap after completion of the
measurement.
Temperature measurement
1. Select °C or °F.
2. The display will indicate the ambient temperature.
Switching off
The moisture measuring device will automatically switch off
after approx. 1 minute if no more measurements are made.
Display lighting
Press the key to activate the display lighting for approx. 15
seconds.

Maintenance and cleaning

After measurement, clean the probes and the case using a clean
cloth.
Never use cleaning agents or solvents. Otherwise the device
may be damaged irreversibly. Plastic parts may be corroded by
chemicals.
.
on the
.
Disposal
Give devices, accessories and packaging to an ecofriendly
recycling.
For EU countries only.
Electrical devices do not go into the domestic
rubbish.
According to the European Directive 2012/19/EU on
electrical and electronic scrap, electrical devices that
are no longer serviceable must be separately collected and
brought to a facility for an environmentally compatible recycling.
Disposal of non-usable batteries
Batteries/accumulators do not fall under domestic
rubbish.
According to the European Directive 2006/66/EC on
batteries and rechargeable
batteries/accumulators
batteries/accumulators, which are no longer usable, to local
collecting points or dealers.

Technical data

Measuring
range:
Building 0,3 – 2,0 %
moisture
Wood moisture 8 – 60 %
Temperatur:
°C 0 – 40 °C
°F 32 – 99 °F
Voltage supply:
Operating conditions:
Storage conditions:
Weight (without battery):
Dimensions (L x W x D)

EC Declaration of Conformity

No. (S-No.): 12378
according to EC directive 2004/108/EC
We,
ATIKA GmbH
Josef-Drexler-Str. 8 – 89331 Burgau – Germany
herewith declare under our sole responsibility that the product
Feuchtemessgerät (Moisture measuring device) FM 2
Serial number: 000001 - 015000
is conform with the above mentioned EC directives as well as
with the provisions of the guidelines below: 2011/65 /EU.
Following harmonized standards have been applied:
EN 61326-1:2013
Keeping of technical documents at:
ATIKA GmbH – Technical department –
Josef-Drexler-Str. 8 – 89331 Burgau – Germany
Burgau, 19.11.2014
accumulators,
must be recycled.
Resolution: Accuracy:
0,01 % ± 0,1 %
0,1 % ± 2 %
0,1 °C ± 2 °C
0,2 °F ± 4 °F
9V (1x 6LR61 / 6AM6)
0 – 40°C
<85% rel. humidity of air
-10 - +50°C
<85% rel. humidity of air
approx. 145 x 60 x 31 mm
i.A.
i.A. G. Koppenstein,
Engineering design management
defective
Bring
93 g
4