Publicidad
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electrical shock and injury to persons, including the following:
Read all instructions before using this Heater.
1.
ALWAYS PLUG HEATERS DIRECTLY INTO A WALL OUTLET/RECEPTACLE. NEVER USE WITH AN EXTENSION CORD. DO NOT
PLUG HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE
OUTLET ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZ-
ARD. PLUG UNIT DIRECTLY INTO A 120V WALL OUTLET ONLY.
WARNING:
FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG
FITS TIGHTLY INTO OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT OVER-
HEATING. IF NECESSARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET.
2.
Use this Heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire,
electrical shock, or injury to persons.
3.
Make certain that the room is equipped with a working smoke detector.
4.
Make certain that the power source conforms to the electrical requirements of the Heater.
5.
Extreme caution is necessary when any Heater is used by or near children or invalids and whenever the Heater is left operating unattended.
6.
The power cord is equipped with a three-prong grounded plug that must be inserted into a matching receptacle. Under no
circumstances should the grounding prong be cut off the plug. Where a two-prong wall receptacle is encountered, it must be
replaced with a properly grounded three-prong receptacle, installed in accordance with the National Electrical Code (NEC) and
all applicable local codes and ordinances. This work must be done only by a qualified electrician, using copper wire only.
WARNING: USE OF A THREE-PRONG TO TWO-PRONG ADAPTER IS NOT RECOMMENDED. IMPROPER
CONNECTION MAY CREATE THE RISK OF ELECTRIC SHOCK. USE OF SUCH ADAPTERS IS NOT
PERMITTED IN CANADA.
7.
Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any man-
ner. Please contact Customer Service at 800-233-0268 Monday through Friday from 8am to 5pm EST for assistance.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING
OR MOVING THE HEATER. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND UNPLUG HEATER BE-
FORE LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE HEATER IS ON OR PLUGGED IN.
8.
To disconnect Heater, turn controls to OFF, then remove plug from outlet.
9.
Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.
10. Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire,
or damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.
11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed,
where openings may become blocked.
12. Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the
Power Cord so the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power
Cord with throw rugs, runners, or similar coverings. Arrange Power Cord away from room traffic and where it will not be tripped over.
13. This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this
Heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from
the front of the Heater and keep them at least 1 foot (0.3 m) from the sides and rear.
14. A Heater has hot and arcing or sparking parts inside. DO NOT use the Heater in areas where gasoline, paint, or flammable liquids
are used or stored. DO NOT use Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres.
This Heater is intended for general use ONLy.
15. This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and
similar indoor locations. NEVER locate a Heater where it may fall into a bathtub or other water container.
16. DO NOT use Heater outdoors.
17. This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined.
Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical
requirements for Agricultural Buildings. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
18. This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state
or local codes or standards relating to electrical requirements for Hazardous locations. THIS HEATER DOES NOT MEET
THE REQUIREMENTS OF NEC ARTICLE 500 (2008).
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK – DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED
CONTROL DEVICES.
SAVE THESE INSTRUCTIONS
Rev. L 7/11
2
FUNCIONAMIENTO
1. Cuidadosamente retire el Calentador de la bolsa y de la caja.
2. Coloque el Calentador sobre una superficie firme y plana.
ADVERTENCIA:
Los tacos de plástico o hule, tales como
las patas de esta unidad, pueden pegarse a la superficie de los
muebles y/o a los pisos de madera. La unidad podría dejar un
residuo capaz de oscurecer, manchar o dejar marcas permanentes
en el acabado de ciertas superficies de muebles, incluyendo
superficies de madera y/o pisos de madera.
3. Conecte el cable a un tomacorriente de 120 voltios. La
Calentador no puede ser tapada en una 220 salida del voltio.
Asegúrese que el enchufe encaje firmemente en el
tomacorriente.
Cuando los enchufes quedan flojos dentro de
los tomacorrientes, podrían deslizarse parcial o
completamente fuera del tomacorriente con el menor
movimiento del cable adosado. Los tomacorrientes
en este estado podrían sobrecalentarse y representar
un peligro de incendio grave; si queda cubierto por
una cortina o tela, el peligro de incendio es todavía
mayor.
4. ENCIENDA el Calentador oprimiendo el Botón de Encendido ( ).
5. Cuando se lo encienda por primera vez, el Calentador mostrará
la temperatura actual de la habitación en ° Fahrenheit. Oprima
los botones ( ) y ( ) al mismo tiempo para cambiar la pantalla a
° Celsius. Oprima los dos botones al mismo tiempo nuevamente
para cambiar la pantalla y volver a ° Fahrenheit.
6. Al encender el Calentador, la unidad estará en calor ALTA ( ) (1500
vatios) y mostrará la temperatura actual de la habitación (Figura 1).
7. Para APAGAR el Calentador, presione el Botón de Encendido
( ) y desconecte el Calentador del tomacorriente eléctrico.
Pantalla al ser encendido por primera vez
Figura 1
FUNCIÓN DE TEMPORIZADOR:
La función de temporizador puede ser activada cuando la pantalla
del Calentador está en cualquier función. (Figura 2) Esta función
le permite fijar la cantidad de tiempo que el Calentador estará
funcionando antes de apagarse automáticamente, de 1 hora
a 8 horas. Presionar el Botón de Temporizador ( ) aumentará
la cantidad de tiempo en 1 hora cada vez que dicho botón sea
oprimido. Después que la pantalla refleje 8 horas, si presiona el
Botón de Temporizador ( ) una vez más, se reiniciará el Calentador
para función continua. El Calentador se apagará cuando el
tiempo fijado haya transcurrido. La unidad puede ser encendida
nuevamente presionando el Botón de Encendido ( ).
5620ES
Rev. L 7/11
MODELO 5620
Función de Temporizador
y Control Automático de
Temperatura
Figura 2
CONTROL AUTOMÁTICO DE TEMPERATURA:
1. Cuando el botón ( ) o el botón ( ) esté presionado, la pantalla
exhibirá la temperatura fijada y el símbolo ( ) aparecerá.
2. Cuando alcance la temperatura en la cual desea establecer
la unidad, la temperatura fijada titilará varias veces y luego
la pantalla volverá a indicar la temperatura actual y cambiará
gradualmente a medida que cambia la temperatura de la
habitación. NOTA: la pantalla de la temperatura no indica la
temperatura del aire caliente emitido por el calentador.
3. Cuando la temperatura del aire alcance los 2° por encima de la
temperatura fijada, el Calentador se apagará.
4. Cuando la temperatura del aire alcance un 1° por debajo de la
temperatura fijada, el Calentador se encenderá.
5. Esta función se cancelará si el botón ( ) es oprimido. El
Calentador ahora estará en calor Alta ( ).
La pantalla refleja la función de Control
Automático de Temperatura
Figura 3
7
(Figura 3)
5620ES
Publicidad
