Briteq BEAMBAR10-RGBW Manual De Instrucciones página 10

ENGLISH
[NO DMX BEHAVIOR]
Used to set how the projector reacts when the DMX-signal suddenly disappears.
 Press the [MODE] or ↑/↓buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ↑/↓ buttons to select the desired mode:
 BLACKOUT
 FREEZE:
 Once the correct option shows on the display, press the [ENTER] button to save it.
Note: as soon as the input detects a DMX-signal, blackout or freeze mode will be cancelled.
[DEFAULT SETTINGS]
This is your emergency exit if you really messed up the settings: just return to factory settings.
Also 2 user settings can be saved/loaded.
 Press the [MODE] or ↑/↓buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ↑/↓ buttons to selected the desired settings:
 FACTORY
 USER1
 USER2
 Press the [ENTER] button:
 FACTORY was selected: the display shows "LOAD"
 Press the [ENTER] button: the display shows "CONFIRM?"
 Use ↑/↓ buttons to select YES / NO
 Press the [ENTER] button to confirm.
 USER1 / USER2 was selected: the display shows "ACTION?"
 Use ↑/↓ buttons to select LOAD / SAVE
 Press the [ENTER] button to confirm: the display shows "CONFIRM?"
 Use ↑/↓ buttons to select YES / NO
 Press the [ENTER] button to confirm.
 SAVE was selected: the current settings of the setup menu are saved to memory.
 LOAD was selected: the previously saved settings are loaded.
PARAMETER name
Ethernet Protocol
DMX Channel mode
SOUND MODE sensitivity
SOUND MODE Chase repeat
AUTO RUN Chase repeat
EFFECT MODE
Flow invert
CUSTOM Static color
MASTER DIM
WHITE BALANCE
DIM Curve
LED behaviour
Auto Lock Menu
No DMX mode
NO DMX blink
[ETHERNET IP ADDRESS]
Used to set the IP address of the projector while controlled using the Ethernet ports.
 Press the [MODE] or ↑/↓buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ↑/↓ buttons to select the desired values for the IP-address.
 Once the correct IP-address shows on the display, press the [ENTER] button to save it.
Remark: an IP address in ArtNet topology generally starts with 2.x.x.x or 10.x.x.x with 255.0.0.0 for netmask.
BRITEQ
®
output turns black while no DMX is detected.
output based on the last valid DMX-signal is kept on the projector.
Defaults Defaults
BEAMBAR 5 BEAMBAR 10
Artnet Artnet
20 CH 40 CH
25 25
3 3
SPEED = 50 SPEED = 50
Repeat = 3 Repeat =3
CFADE
CFADE speed=50
speed=50
+ FL = 00
+ FL = 00
OFF OFF
RGBW = 255 RGBW = 255
100% 100%
RGBW = 255 RGBW = 255
Square Square
Halogen Halogen
OFF OFF
Freeze Freeze
ON ON
USER defaults 1
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current custom color settings
Current setting in the menu
Current white balance settings
for all pixels are saved
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
8/86
OPERATION MANUAL
USER defaults 2
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current custom color settings
Current setting in the menu
Current white balance settings
for all pixels are saved
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
BEAMBAR5+10-RGBW