Safety Notes - Modellsport MULTIPLEX AcroMaster Instrucciones

! These operating instructions are an integral part of the
product. They contain important information and safety
notes, and should be kept in a safe place at all times. Be
sure to pass them on to the new owner if you ever dispose
of the product.
1. I
NTRODUCTION
The power set "AcroMaster" and "Gemini TUNING" # 33
2640, consists of perfectly harmonized components.
It allows you to use the AcroMaster and comparable
models with the 10" x 5" propeller as a trainer and for ba-
sic aerobatics. Using the 11" x 5.5" propeller allows you to
fly the complete 3D aerobatic program.
For use with the model Gemini and comparable models,
we recommend the 10" x 5" propeller to give the model an
extreme high drive power. Therefore even 3D aerobatic
figures are feasible with our biplane Gemini.
2. C / R
ONTENTS
• 1 Himax C 3516-1130 motor
• 1 MULTIcont BL-54 BL speed controller
• 1 10" x 5" propeller
• 1 11" x 5.5" propeller
• 1 propeller driver and nut for ELAPOR spinner
Motor shaft-Ø 5mm, Prop-shaft 6 mm
• 1 motor mount „AcroMaster" for assembling in the model
Gemini
• Various small items for installation in the model
Options:
• ELAPOR 62 mm Ø spinner incl. holder
• Propeller driver and spinner for motors with 5 mm Ø shaft,
prop bore 6 mm
3. T . O
YP PERATIONAL
S "A M
ET CRO ASTER
AcroMaster
3S LiPo / Prop: 10" x 5"
3S LiPo / Prop: 11" x 5.5"
Recommended Battery for AcroMaster:
MULTIPLEX Li-BATT BX 3/2500
MULTIPLEX Li-BATT BX 3/3200
Gemini TUNING
3S LiPo / Prop: 10" x 5"
Recommended Battery for Gemini TUNING:
MULTIPLEX Li-BATT BX 3/2100
MULTIPLEX Li-BATT BX 3/2500
If you use the Himax C 3516-1130 motor and the stan-
dard propellers supplied in the set, do not use more than
a 3S LiPo pack or 9 NiXX cells
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de
www.modellmarkt24.ch www.modellmarkt24.ch
Ope ra t ing I nst ruc t ions for Pow e r Se t
„Ac roM a st e r" a nd „Ge m ini T U N I N G"
EPLACEMENT PARTS
D P
ATA OF OWER
" . "G TUNING"
A EMINI
Current drain: approx. 30.0 A
Current drain: approx. 34.0 A
Current drain: approx. 30.0 A
.
S
4. AFETY
The power set "AcroMaster" and Gemini TUNING" is de-
signed exclusively for use in modelling applications. In-
correct use can result in serious personal injury.
• Read the instructions before initiation
• Before every flight, check that the motor and propeller
are securely mounted
• Remove all movable objects from the area around the
propeller before switching the motor on
• Do not allow clothing or any of your extremities to get
close to the spinning propeller
• Never run the motor in your hand
• Switch the motor off immediately if you notice vibration.
Eliminate the cause of the vibration before running it
again; you may need to correct the balance of the pro-
peller
• Make sure the power system is adequately cooled; do
not allow anything to obstruct the free circulation of air
# 33 3023
# 7 2277 5. A
SSEMBLING
# 73 3106
"A M
CRO
# 73 3179
# 33 2326
# 22 4207
# 33 2315
1. Screw the motor to the motor mount.
For assembling in the model Gemini, please use the
motor mount „AcroMaster", supplied in this power set
ensure that the motor is free to rotate. When
deploying the motor cables, check that they cannot
# 15 7191
make contact with the spinning motor. Secure the
# 15 7136
motor leads with Velcro tape or similar.
2. Fit the split taper collet and the propeller driver on the
motor shaft.
3. Fit the propeller and the spinner holder on the propeller
driver, and secure them with the nut for the ELAPOR
spinner (supplied).
# 15 7131
4. Clip the ELAPOR spinner onto the spinner holder.
# 15 7191
N
OTES
O T P
F HE OWER
" G
ASTER AND EMINI
S
ET
TUNING"
Page 1/2