OHAUS Compass CX Serie Guia De Inicio Rapido página 2

SAFETY PRECAUTIONS

Only operate the scale in dry locations.

Do not operate the scale in hazardous locations.

Do not drop or overload the scale.

When operating the scale from mains power, only use the AC
Adapter specified by OHAUS.
INSTALLATION

Remove the plastic transportation protective insert (0.1g model only)
for use. Save the plastic insert to ensure safe transport. See figure
1.

Remove the battery cover on bottom of the scale and insert the 3
LR6 (AA) batteries into the battery compartment. See figure 2.
TWO BUTTON KEYPAD

: Press to turn the scale on / set zero. Long press to turn the
scale off.

: Press to change units. Long press to enter user menu.
CALIBRATION
Long press until [CAL] is displayed. Press
1. Press to set the zero point.
2. When [xxx] is displayed, place xxx g weight on the platform.
3. Press to set the span point.
4. After calibration, the display returns to weighing.
BACKLIGHT
1. Long press until [CAL] is displayed. Press
next menu b.Auto.
to move to next menu b.ON / b.OFF. Press
2. Press
accept displayed setting and return to weighing.
MAINTENANCE

The exterior surfaces of the instrument may be cleaned with a cloth
dampened with water and a mild detergent. Do not use solvents,
harsh chemicals, ammonia or abrasive cleaning agents.

Register your scale under Warranty Registration at
www.ohaus.com/support.
For technical issues contact an Authorized OHAUS Service Agent.
Please visit our website www.ohaus.com to locate the OHAUS office
nearest you.
COMPLIANCE
This product complies with Directives 2011/65/EU (RoHS),
2014/30/EU (EMC) and 2014/35/EU (LVD). The EU
Declaration of Conformity is available online at
www.ohaus.com/ce.
This product complies with the EU Directive 2012/19/EU
(WEEE). For disposal instructions in Europe, refer to
www.ohaus.com/weee
en
FCC NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by OHAUS Corporation
could void the user's authority to operate the equipment.
to start calibration.
to move to
to
Visit us at www.TestEquipmentDepot.com
99 Washington Street
Melrose, MA 02176
Phone 781-665-1400
Toll Free 1-800-517-8431
Figure 1 / Figura 1 / Figure 1
Figure 2 / Figura 2 / Figure 2
Technical Data / Datos Té cnicos / Données Techniques
Model Max d
CX221 220 0.1 g
CX621 620 0.1 g
CX1201 1200 0.1 g
CX2200 2200 1 g
CX5200, CX5200F* 5200 1 g
*Carrying case is standard in CX5200F model.
Please scan the below
QR code to download
the user manual:
*30467748*
P/N 30467748 A  2018 Ohaus Corporation, all rights reserved.
Printed in China