Ryobi RHT2660R Manual De Utilización página 19

Deutsch (Übersetzung der originalen Anleitungen)
5. Pull the starter grip until the engine attempts to start.
6. Set the choke lever to "Half" choke position.
7. Pull the starter grip until the engine starts.
8. Allow the engine to run for 6-10 seconds, then set the choke
lever to "Run" position.
9. Squeeze the throttle lock and throttle trigger to run.
NOTE: Before squeezing and releasing the throttle trigger,
ensure that the choke lever is at "Run" position.
To start a warm engine:
1. Set the choke lever to "Run" position.
2. Pull the starter grip until the engine starts.
To stop the engine:
Press and hold the on/off switch to the " O " position until the
engine stops.
·
WARNINg
When the engine starts with the trigger locked,
the blades will move. Keep body, objects, and
obstructions away from blades. Failure to keep away
from the blades can result in serious injury.
ROTATINg THE HANDLE (Fig. 4)
The handle can be rotated 45
To rotate handle:
Shut off the hedge trimmer.
■
Disengage the throttle trigger.
■
Pull back on the rotating handle knob.
■
Turn handle to the right or to the left.
■
Release rotating handle knob.
■
Keep turning handle until it locks into place in one of the
■
45 o or 90 o positions.
NOTE: The trimmer will only operate at one of these locked
positions. The handle is locked when the rotating
handle knob is securely into place, is not extended,
and the handle will no longer move to either side.
CUTTINg TIpS
WARNINg
Always keep both hands on the hedge trimmer
handles. Never hold shrubs with one hand and
operate hedge trimmer with the other. Failure to heed
this warning can result in serious injury.
WARNINg
TO STOP THE ENGINE IN AN EMERGENCY:
Press and hold the on/off switch in the stop " O "
position until the engine stops.
WARNINg
Clear the area to be cut before each use. Remove
all objects such as cords, lights, wire, or loose string
which can become entangled in the cutting blade and
create a risk of serious personal injury.
Do not force the hedge trimmer through heavy shrubbery.
■
This can cause the blades to bind and slow down. If the
blades slow down, reduce the pace.
Do not attempt to cut stems or twigs that are larger than
■
28 mm. thick, or those obviously too large to feed into the
cutting blade. Use a non-powered hand saw or pruning
saw to trim large stems.
If blades do become jammed, stop the engine, allow the
■
blades to stop, remove the spark plug wire and remove the
English (Original instructions)
o or 90 o to the left or to the right.
obstruction.
If desired, you can use a string to help cut your hedge
■
level. Decide how high you want the hedge. Stretch a
piece of string along the hedge at the desired height. Trim
the hedge just above the guide line of string. Trim the side
of a hedge so that it will be slightly narrower at the top.
More of the hedge will be exposed when shaped this way,
and it will be more uniform.
Always wear gloves when using the hedge trimmer. When
■
trimming new growth, use a wide sweeping action, so
that the stems are fed directly into the cutting blade. Older
growth will have thicker stems and will be trimmed easiest
by using a sawing movement.
It has been reported that vibrations from hand-held tools
■
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the fi ngers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices
are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
a. Keep your body warm in cold weather. When operating the
unit wear gloves to keep the hands and wrists warm. It is
reported that cold weather is a major factor contributing to
Raynaud's Syndrome.
b. After each period of operation, exercise to increase blood
circulation.
c. Take frequent work breaks. Limit the amount of exposure
per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about these
symptoms.
OpERATINg THE HEDgE TRIMMER (Fig. 5)
WARNINg
Read the safety information for safe operation using
the blade. Extreme care must be taken when using
blades to ensure safe operation. Refer to Specific
Safety Rules.
Always hold the hedge trimmer with both hands when
■
operating. Use a firm grip on the handles. The unit is used
for cutting in either direction in a slow, sweeping action
from side to side.
The hedge trimmer should be positioned so that your body
■
will not come into contact with the silencer or the power
head. Stand so that you are stable and balanced on both
feet.
Inspect and clear the area of any hidden objects. Never cut
■
or trim anywhere you cannot clearly see the entire length
of the blades.
Never use the hedge trimmer near power lines, fencing,
■
posts, buildings, or other immovable objects.
Never use a blade after hitting a hard object without first
■
inspecting it for damage. Do not use if any damage is
detected.
MAINTENANCE
WARNINg
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
17